[TrunkCom] Control Frequency Only Mode

[Jeff Kenyon]

Hi Rich, how did you figure this out/  I don't see how this can work.





On Thu, 27 Oct 2005, bearcat wrote:

> This will work with EDACS and LTR, use the 250 because I know it works
> with that radio, I see no reason it would not work with the PRO 96,
> however if you use the 96 leave the first channel blank ie 000, 100,
> 200, 300 start with ch 1 ie 001, 101, 201  The 96 will tell you the LCN
> # of the control channel so you have one the LCNs right off the bat.
>
> Pick one freq from your EDACS or LTR system.
>
> Program that freq into the first 20 channels of bank one, yes the same
> freq 20 times.
>
> Scan that bank.
>
> When a conversation appears on a channel press hold and not the channel
> no. ie 003 or 011 whatever.  That will correspond to the LCN #  so 003
> would be LCN 3 or 011 would be LCN 11
>
> Now pick the next freq, put that freq in every channel except the first
> on you found so if it was 003 leave the original freq in 003.  So you
> will enter the 2nd freq 19 times.
>
> Scan that bank
>
> When a conversation appears on a channel press hold and not the channel
> no. ie 005 or 013 whatever.  That will correspond to the LCN #  so 005
> would be LCN 5 or 013 would be LCN 13
>
> Continue the process until you have done this with every freq on the
> system in the end you will know the LCNs for all of the freqs.
>
> One note if you hear more than one control channel on your EDACS system
> on the air at the same time then it is a multisite system and needs to
> be programmed in two different banks
>
> Rich
>
>
>
>
> -----Original Message-----
> From: trunkcom-bounces at mailman.qth.net
> [mailto:trunkcom-bounces at mailman.qth.net] On Behalf Of Jeff Kenyon
> Sent: Thursday, October 27, 2005 8:48 AM
> To: Discussion of Monitoring Trunk Radio Systems
> Subject: RE: [TrunkCom] Control Frequency Only Mode
>
>
> Hi Rich, i would be interested to know tihs trick.  Does it work with
> all EDACS capable scanners or just some of htem?  The two scanners I use
> or can use for EDACS arte the 250 and Pro-96.
>
>
>
>
>
> On Wed, 26 Oct 2005, bearcat wrote:
>
> > Reading between the lines, are you also looking for a way to find what
>
> > the LCN #s are ?
> >
> > There is a trick with the scanner you can do.
> >
> > I am not going to type it out unless you are looking for the info
> >
> > Rich
> >
> >
> >
> > _______________________________________________
> > TrunkCom mailing list
> > mailto:TrunkCom at mailman.qth.net
> > http://mailman.qth.net/mailman/listinfo/trunkcom
> >
> > Mailman: User Guide for List Subscribers
> > http://mailman.qth.net/subscribers.htm
> >
> _______________________________________________
> TrunkCom mailing list
> mailto:TrunkCom at mailman.qth.net
> http://mailman.qth.net/mailman/listinfo/trunkcom
>
> Mailman: User Guide for List Subscribers
> http://mailman.qth.net/subscribers.htm
>
>
> _______________________________________________
> TrunkCom mailing list
> mailto:TrunkCom at mailman.qth.net
> http://mailman.qth.net/mailman/listinfo/trunkcom
>
> Mailman: User Guide for List Subscribers
> http://mailman.qth.net/subscribers.htm
>