[R-1051] R-1051 Mounting brackets

[Nick England]

Angle aluminum is usually available at good hardware stores and big
boxes like Home Despot, sLowe's, etc.- 1/2" up to 2" sides - it may be
on display with sheet aluminum and not at the same place as angle iron
& steel straps.
Nick K4NYW
www.navy-radio.com

On Tue, Dec 7, 2010 at 8:05 PM, Chris Kucera <chris.kucera at gmail.com> wrote:
> I will have to see if I can find some angle iron that is big enough for the
> bracket.  Most everything I see at the Big R is flat pieces and that angle
> iron that has the holes on both sides.
>
> ----- Original Message -----
> From: "paul swed" <paulswedb at gmail.com>
> To: "R-1051 Discussion Group" <r-1051 at mailman.qth.net>
> Sent: Tuesday, December 07, 2010 2:56 PM
> Subject: Re: [R-1051] R-1051 Mounting brackets
>
>
>> As I mentioned get angle iron its already bent 90 degrees.
>> All you do is cut it and then drill holes.
>> Did that 10 plus years ago and the brackets are holding a 1051 and also a
>> RT
>> unit of the same ilk.
>> Boy been a while I don't remember the RT unit model number.
>>
>> On Tue, Dec 7, 2010 at 3:38 PM, Chris Kucera <chris.kucera at gmail.com>
>> wrote:
>>
>>> I'd buy a set for 25 bucks a set also.  It would be easier than the
>>> hammer
>>> and vise trick I'm thinking about doing.
>>>
>>> On Tue, Dec 7, 2010 at 10:53 AM, mikea <mikea at mikea.ath.cx> wrote:
>>>
>>> > On Tue, Dec 07, 2010 at 12:35:35PM -0500, Tony Snider wrote:
>>> > > what do you guys feel a fair price per set would be??  I have a good
>>> > friend
>>> > > that runs a milspec metal shop and could make these with his eyes
>>> > closed..
>>> > > maybe I could do an run of maybe 100 sets.   I could use maybe 10
>>> > > sets.
>>> > they
>>> > > will be made on a press with punched out holes.  quality just like
>>> > originals
>>> > >
>>> > > they would be just the plates with drilled holes and the mounting
>>> > > ears.
>>> > with
>>> > > no side holes or rear supports (hopefully your radio room wont
>>> experiance
>>> > > heavy seas)
>>> > >
>>> > > I could have them milspec painted haze gray or not  what are your
>>> > thoughts??
>>> > >
>>> > > they will fit all models of R-1051 , T-827, RT-618
>>> > >
>>> > > I could make them for the AM-3007 and the 1KW amp also if any
>>> > > interest
>>> >
>>> > I'd buy 3 sets at $25/set, I would indeed.
>>> >
>>> > --
>>> > Mike Andrews, W5EGO
>>> > mikea at mikea.ath.cx
>>> > Tired old sysadmin
>>> > ______________________________________________________________
>>> >  R-1051 mailing list
>>> > Home: http://mailman.qth.net/mailman/listinfo/r-1051
>>> > Help: http://mailman.qth.net/mmfaq.htm
>>> > Post: mailto:R-1051 at mailman.qth.net
>>> >
>>> > This list hosted by: http://www.qsl.net
>>> > Please help support this email list: http://www.qsl.net/donate.html
>>> >
>>> ______________________________________________________________
>>> R-1051 mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/r-1051
>>> Help: http://mailman.qth.net/mmfaq.htm
>>> Post: mailto:R-1051 at mailman.qth.net
>>>
>>> This list hosted by: http://www.qsl.net
>>> Please help support this email list: http://www.qsl.net/donate.html
>>>
>> ______________________________________________________________
>> R-1051 mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/r-1051
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:R-1051 at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>
> ______________________________________________________________
> R-1051 mailing list
> Home: http://mailman.qth.net/mailman/listinfo/r-1051
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:R-1051 at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>