[ICOM] PW-1 problem

[Woody]

My apologies to the list.  I hit the wrong button

73,

Woody
KJ4SO
  ----- Original Message ----- 
  From: Woody 
  To: ICOM Reflector 
  Sent: Wednesday, December 29, 2004 11:41 PM
  Subject: Re: [ICOM] PW-1 problem


  I found the message below after I sent you the last message.

  Never Mind :-)


    ----- Original Message ----- 
    From: Dr. Howard S. White 
    To: ICOM Reflector 
    Sent: Wednesday, December 29, 2004 11:01 PM
    Subject: Re: [ICOM] PW-1 problem


    I have mine set at:

    CI-V Baud Rate            19200
    CI-V Address                64h
    CI-V Transceive            ON
    CI-V with IC-731        OFF

    Works perfectly once they sych

    __________________________________________________________
    Howard S. White Ph.D. P. Eng., VE3GFW/K6

    "No Good Deed Goes Unpunished"

    ----- Original Message ----- 
    From: "Steve N4LQ" <n4lq at iglou.com>
    To: "ICOM Reflector" <icom at mailman.qth.net>
    Sent: Wednesday, December 29, 2004 7:10 PM
    Subject: Re: [ICOM] PW-1 problem


    > You do need to set the speed to 9600 bps on the PROII so it can talk to
    the
    > PW1 then go through the resetting procedure on the PW1 console. Also try
    > plugging the pw1 directly into the PRO to eliminate possibility of CT-17
    > problems....just to check things out. Finally, I believe you must set the
    > menu on the PRO for IC735 transcieve, or at least I did here.
    >
    > Steve N4LQ
    > ----- Original Message ----- 
    > From: "Chuck Kresge" <du3nxe at mozcom.com>
    > To: "ICOM Reflector" <icom at mailman.qth.net>
    > Sent: Wednesday, December 29, 2004 12:26 PM
    > Subject: [ICOM] PW-1 problem
    >
    >
    > >I need some help with my new PW-1.
    > >
    > > I have an IC-756PROII and just received a PW-1 amplifier. During the
    > > separation of the remote controller from the amplifier I noticed on page
    > > 10
    > > of the PW-1 manual in step 8 it says "Connect the grounding wire as
    shown
    > > below." I never could find that grounding wire and cannot see it in the
    > > illustration and then continued to complete the separation of the remote
    > > controller. My amplifier is working with my IC-756PROII except that I
    > > cannot
    > > get the amplifier to automatically change bands with the PW-1 and my
    CT-17
    > > installed with my computer.
    > >
    > > Can someone give me information on this grounding wire?
    > >
    > > Thanks very much-Chuck Kresge DU3NXE du3nxe at mozcom.com
    > >
    > > ----
    > > Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
    > > Win a new Icom IC-756 PRO III and help QSL/QTH.net
    > > Details at: http://mailman.qth.net/
    > >
    >
    > ----
    > Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
    > Win a new Icom IC-756 PRO III and help QSL/QTH.net
    > Details at: http://mailman.qth.net/

    ----
    Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
    Win a new Icom IC-756 PRO III and help QSL/QTH.net
    Details at: http://mailman.qth.net/
  ----
  Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
  Win a new Icom IC-756 PRO III and help QSL/QTH.net
  Details at: http://mailman.qth.net/