[ICOM] PW-1 problem

[Woody]

I found the message below after I sent you the last message.

Never Mind :-)


  ----- Original Message ----- 
  From: Dr. Howard S. White 
  To: ICOM Reflector 
  Sent: Wednesday, December 29, 2004 11:01 PM
  Subject: Re: [ICOM] PW-1 problem


  I have mine set at:

  CI-V Baud Rate            19200
  CI-V Address                64h
  CI-V Transceive            ON
  CI-V with IC-731        OFF

  Works perfectly once they sych

  __________________________________________________________
  Howard S. White Ph.D. P. Eng., VE3GFW/K6

  "No Good Deed Goes Unpunished"

  ----- Original Message ----- 
  From: "Steve N4LQ" <n4lq at iglou.com>
  To: "ICOM Reflector" <icom at mailman.qth.net>
  Sent: Wednesday, December 29, 2004 7:10 PM
  Subject: Re: [ICOM] PW-1 problem


  > You do need to set the speed to 9600 bps on the PROII so it can talk to
  the
  > PW1 then go through the resetting procedure on the PW1 console. Also try
  > plugging the pw1 directly into the PRO to eliminate possibility of CT-17
  > problems....just to check things out. Finally, I believe you must set the
  > menu on the PRO for IC735 transcieve, or at least I did here.
  >
  > Steve N4LQ
  > ----- Original Message ----- 
  > From: "Chuck Kresge" <du3nxe at mozcom.com>
  > To: "ICOM Reflector" <icom at mailman.qth.net>
  > Sent: Wednesday, December 29, 2004 12:26 PM
  > Subject: [ICOM] PW-1 problem
  >
  >
  > >I need some help with my new PW-1.
  > >
  > > I have an IC-756PROII and just received a PW-1 amplifier. During the
  > > separation of the remote controller from the amplifier I noticed on page
  > > 10
  > > of the PW-1 manual in step 8 it says "Connect the grounding wire as
  shown
  > > below." I never could find that grounding wire and cannot see it in the
  > > illustration and then continued to complete the separation of the remote
  > > controller. My amplifier is working with my IC-756PROII except that I
  > > cannot
  > > get the amplifier to automatically change bands with the PW-1 and my
  CT-17
  > > installed with my computer.
  > >
  > > Can someone give me information on this grounding wire?
  > >
  > > Thanks very much-Chuck Kresge DU3NXE du3nxe at mozcom.com
  > >
  > > ----
  > > Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
  > > Win a new Icom IC-756 PRO III and help QSL/QTH.net
  > > Details at: http://mailman.qth.net/
  > >
  >
  > ----
  > Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
  > Win a new Icom IC-756 PRO III and help QSL/QTH.net
  > Details at: http://mailman.qth.net/

  ----
  Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
  Win a new Icom IC-756 PRO III and help QSL/QTH.net
  Details at: http://mailman.qth.net/