[Elecraft] FW: K3 - SSB audio get lost !

[Vic Goncharsky]

Can you hear signals in CW mode with both narrow and wide Xtal filters?
Please look into schematic diagram and using the signal generator try to find where the signal is lost in front-end or IF chain.
 Go backwards from AF to front-end.
 
73, Victor Goncharsky US5WE/K1WE (UW5W in VHF contests)
UARL Technical Committee
DXCC card checker in Ukraine(160 meters).
--------------------------------------------
On Thu, 10/24/13, Tommy <aldermant at windstream.net> wrote:

 Subject: [Elecraft] FW:  K3 - SSB audio get lost !
 To: Elecraft at mailman.qth.net
 Date: Thursday, October 24, 2013, 2:22 AM
 
  
 
  
 
 From: Tommy [mailto:aldermant at windstream.net]
 
 Sent: Wednesday, October 23, 2013 10:17 PM
 To: 'elecraft-bounces at mailman.qth.net'
 Subject: RE: [Elecraft] K3 - SSB audio get lost !
 
  
 
 Thanks to all asking about my filter configuration.
 
  
 
 I have my 2.7kc/1.0kc/0.5kc/0.3kc filters all enabled for
 CW/ LSB/ USB/ and
 DATA.
 
  
 
 And to clarify my original post, I am talking about receive
 audio and not
 transmitted audio. 
 
  
 
 73,
 
 Tom - W4BQF
 
  
 
  
 
  
 
 From: John Parker [mailto:johnj1jr at verizon.net]
 
 Sent: Wednesday, October 23, 2013 10:04 PM
 To: Tommy
 Subject: Re: [Elecraft] K3 - SSB audio get lost !
 
  
 
 Is it possible that your 2.7/2.8 Khz filter is not selected
 for SSB in the
 configuration?
 
 Good luck with this, 73, John WB4UHC
 
  
 
  
 
   _____  
 
 From: Tommy <aldermant at windstream.net
 <mailto:aldermant at windstream.net>
 >
 To: elecraft at mailman.qth.net
 <mailto:elecraft at mailman.qth.net> 
 
 Sent: Wednesday, October 23, 2013 10:39 AM
 Subject: [Elecraft] K3 - SSB audio get lost !
 
 
 I am having a configuration issue that I have spent hours
 trying to figure
 out and need some help please.
 
 As a CW person, I seldom operate SSB and I am trying to get
 set up for this
 weekend's CQWW SSB test. Below are some of my configuration
 for my K3 and
 the attached are jpg configuration sheets from K3 EZ. In any
 band in the SSB
 portion, I have no audio output any time I am in the USB or
 LSB mode,
 however if I change from USB to CW, I have normal audio but
 of course I
 can't copy the SSB signals. This is true whether I have my
 SUB turned on or
 not. I have my CM-500 headset plugged into the rear of my K3
 and I have the
 RS20S headset plugged into the front panel PHONES jack and I
 have no audio
 with either or both of the headsets plugged in. With both
 headsets removed,
 I have no speaker audio in the SSB mode, but normal audio in
 the CW or AM
 mode.
 
 Any helpful suggestions would be greatly appreciated!
 
 In CONFIG I have:
 
 SPKRS = 1
 SPKR+PH = YES
 L-MIX-R = A  b
 
 Thanks for your input and 73,
 
 Tom - W4BQF
 
 PS: I have been trying to configuration pictures from K3-EZ
 but nothing is
 getting onto the reflector.
 
 ______________________________________________________________
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft at mailman.qth.net
 <mailto:Elecraft at mailman.qth.net>
 
 
 This list hosted by: http://www.qsl.net <http://www.qsl.net/> 
 Please help support this email list: http://www.qsl.net/donate.html
 
 ______________________________________________________________
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft at mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html