[Elecraft] Setting RS232 baudrate

[Dan Atchison]

 And, I'm sure the P3 communicates with the K3 for a reason.  Why would you want to communicate at a lower speed, anyway?

 


Dan -- N3ND

 

 

-----Original Message-----
From: Dick Dievendorff <dieven at comcast.net>
To: 'Dick Dievendorff' <dieven at comcast.net>; 'Dick Grolleman' <groll064 at planet.nl>; elecraft at mailman.qth.net
Sent: Tue, Sep 14, 2010 10:11 am
Subject: Re: [Elecraft] Setting RS232 baudrate


I didn't read your note carefully enough.

As W4TV correctly points out, the P3 to K3 speed is always 38400.  The PC to
P3 speed can be set to 4800 using the P3 front panel or the BR command.

Dick, K6KR



-----Original Message-----
From: elecraft-bounces at mailman.qth.net
[mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Dick Dievendorff
Sent: Tuesday, September 14, 2010 6:22 AM
To: 'Dick Grolleman'; elecraft at mailman.qth.net
Subject: Re: [Elecraft] Setting RS232 baudrate

Dick, try this to set your speed to 4800:

Start the K3 Utility.
On the Port tab, press "Test communications".  The K3 Utility should find
the radio at any of the supported speeds.
Go to the command tester tab.  Type "BR0;" (including the semicolon, but not
the quotes) to choose 4800 bps.
Go to the port tab and press "Test communications". Hopefully the radio will
be at 4800 bps.
Press the K3 power button to turn it off.  During power-down, the K3 should
write the current selected speed to EEPROM for the next power up.
Press the K3 power button to turn it back on.  Press "test communications".
The radio should now be at 4800 bps.

73 de Dick, K6KR




-----Original Message-----
From: elecraft-bounces at mailman.qth.net
[mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Dick Grolleman
Sent: Tuesday, September 14, 2010 6:11 AM
To: elecraft at mailman.qth.net
Subject: [Elecraft] Setting RS232 baudrate

HI ALL

Just installed version 4.05 in my K3 to run my P3 as well
I always used the microkeyer at 4800 baud from the K3, but I'm not able
anymore to set any other speed in the K3 as 38400. Yes I can change it, but
the radio does not store it when I leave the menu. And I just can't get it
to work on 38400, don't know why.

So now my micro keyer is not reading the Radio
any solutions?

73 de Dick PA3FQA
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html