[Elecraft] Setting RS232 baudrate

[Dick Grolleman]

Thanks Joe and Dick

All working agn

73 de Dick

----- Original Message ----- 
From: "Dick Dievendorff" <dieven at comcast.net>
To: "'Dick Dievendorff'" <dieven at comcast.net>; "'Dick Grolleman'" 
<groll064 at planet.nl>; <elecraft at mailman.qth.net>
Sent: Tuesday, September 14, 2010 4:11 PM
Subject: RE: [Elecraft] Setting RS232 baudrate


>I didn't read your note carefully enough.
>
> As W4TV correctly points out, the P3 to K3 speed is always 38400.  The PC 
> to
> P3 speed can be set to 4800 using the P3 front panel or the BR command.
>
> Dick, K6KR
>
>
>
> -----Original Message-----
> From: elecraft-bounces at mailman.qth.net
> [mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Dick Dievendorff
> Sent: Tuesday, September 14, 2010 6:22 AM
> To: 'Dick Grolleman'; elecraft at mailman.qth.net
> Subject: Re: [Elecraft] Setting RS232 baudrate
>
> Dick, try this to set your speed to 4800:
>
> Start the K3 Utility.
> On the Port tab, press "Test communications".  The K3 Utility should find
> the radio at any of the supported speeds.
> Go to the command tester tab.  Type "BR0;" (including the semicolon, but 
> not
> the quotes) to choose 4800 bps.
> Go to the port tab and press "Test communications". Hopefully the radio 
> will
> be at 4800 bps.
> Press the K3 power button to turn it off.  During power-down, the K3 
> should
> write the current selected speed to EEPROM for the next power up.
> Press the K3 power button to turn it back on.  Press "test 
> communications".
> The radio should now be at 4800 bps.
>
> 73 de Dick, K6KR
>
>
>
>
> -----Original Message-----
> From: elecraft-bounces at mailman.qth.net
> [mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Dick Grolleman
> Sent: Tuesday, September 14, 2010 6:11 AM
> To: elecraft at mailman.qth.net
> Subject: [Elecraft] Setting RS232 baudrate
>
> HI ALL
>
> Just installed version 4.05 in my K3 to run my P3 as well
> I always used the microkeyer at 4800 baud from the K3, but I'm not able
> anymore to set any other speed in the K3 as 38400. Yes I can change it, 
> but
> the radio does not store it when I leave the menu. And I just can't get it
> to work on 38400, don't know why.
>
> So now my micro keyer is not reading the Radio
> any solutions?
>
> 73 de Dick PA3FQA
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>