[Elecraft] RE: Plans for a pre-built Rascal digital interface for the Elecraft K2?

Tue Apr 16 12:04:01 2002

That sounds like a good idea; though most Elecraft 
owners are, by nature, kit builders.  

However, there are quite a few Elecraft owners who had 
someone build the kit for them because they, for many 
reasons, cannot or do not want to do it themselves.  For 
those folks, the option you state below, would probably 
be an excellent product.  They could order it and would 
be able to easily find someone to wire the plug for them.

I am also sending this to the Elecraft reflector so 
people can comment.

If you want, I will forward any comments from the 
reflector to you.

Cheers,
Chuck
KG6GUF

-----Original Message-----
From: BUX CommCo [mailto:[email protected]]
Sent: Tuesday, April 16, 2002 11:38 AM
To: Charles Bybee
Subject: RE: Plans for a Rascal for the Elecraft K2?
Importance: High

I suppose I could build it and leave the 8 pin PLUG for 
the K@ users to
complete...
I can do that... HI

73 de BucK4ABT

-----Original Message-----
From: Charles Bybee [mailto:[email protected]]
Sent: Tuesday, April 16, 2002 8:33 AM
To: 'BUX CommCo'; Charles Bybee
Subject: RE: Plans for a Rascal for the Elecraft K2?

Point taken.  Perhaps you could produce a mind->kit 
interface that would do
the work automatically... hihi.

Cheers,
Chuck
KG6GUF

-----Original Message-----
From: BUX CommCo [mailto:[email protected]]
Sent: Tuesday, April 16, 2002 11:30 AM
To: Charles Bybee
Subject: RE: Plans for a Rascal for the Elecraft K2?
Importance: High

I cannot produce a NON-KIT version... as the K2 Manual 
allows the builter to
wire the MIC to his/her preference.... kind of hard to 
read all those
minds... hihi.

73 de BucK4ABT

-----Original Message-----
From: Charles Bybee [mailto:[email protected]]
Sent: Tuesday, April 16, 2002 8:19 AM
To: 'BUX CommCo'
Subject: RE: Plans for a Rascal for the Elecraft K2?

Yep, I missed it at first.  It isn't shown on the main 
page for the Rascal.
Perhaps you should add it to the list, or don't you 
produce a non-kit
version?

I have ordered it from you.  Thank you.

Cheers,
Chuck
KG6GUF

-----Original Message-----
From: BUX CommCo [mailto:[email protected]]
Sent: Tuesday, April 16, 2002 11:15 AM
To: Charles Bybee
Subject: RE: Plans for a Rascal for the Elecraft K2?
Importance: High

Did you miss it????
It's on the web page at:

www.PacketRadio.com/psk31.htm

73 de BucK4ABT
For PSK31, SSTV, and WSJT, SoundCard to Transceiver 
Interfaces, VISIT:
www.PacketRadio.com/psk31.htm
For Radio to TNC interfaces, VISIT:
www.packetradio.com/Radio-TNC%20Wiring%20Diagrams.htm
For Antennas, Accessories, and Connectors, VISIT:
www.BUXcomm.com
www.BUXcommCO.com
www.BucksCommCo.com
www.BuckCommCo.com
For the PSK31 Tutorial, Visit:
www.packetradio.com/bbbb.htm
For Antennas, Accessories, and Connectors for HAM radio, 
VISIT:
www.BUXcommco.com
www.BUXcomm.com
For topics of interest to all HAMs, VISIT:
www.PacketRadio.com
www.AmateuRadio.org

-----Original Message-----
From: Charles Bybee [mailto:[email protected]]
Sent: Tuesday, April 16, 2002 7:58 AM
To: '[email protected]'
Subject: Plans for a Rascal for the Elecraft K2?

Any plans for the Elecraft K2 Rascal?

I think it would be close to the Kenwood but not sure.

See www.elecraft.com.

Cheers,
Chuck
KG6GUF