[Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig

[Radivoj Kar, F6GNZ]

Thanks Joe ! I have created an additional port for COM2 and set Omni-rig to this port with 1200 ms polling time (DX4WIN polls each 500ms). All works fine except when I select both Sync from Omni-Rig and Sync to Omni-rig to be able to set TX to RX-ed frequency but also to set RX frequency by clicking on the DX4WIN spots. In this case my IC706 starts to "walk" frequencies, like it had gone to the scanning mode....So, must chose only one way sync...

best 73, Radi F6GNZ





>________________________________
> De : "Joe Subich, W4TV" <lists at microham-usa.com>
>À : f6gnz <f6gnz at yahoo.com>; microham <microHAM at yahoogroups.com> 
>Envoyé le : Samedi 22 juin 2013 15h02
>Objet : Re: [microHAM] MicroKeyer2,  DX4WIN, HDSDR and Omni-Rig
> 
>
>
>If you are trying to configure a splitter function, you could try
>connecting HDSDR/OmniRig to Router's 2nd CAT port.  Otherwise, your
>logger developer will probably need to provide an OmniRig option
>where OmniRig serves both HDSRD and the logger.
>
>Note, if you use Router's 2nd CAT port, it will be necessary to set any
>polling from HDSDR/OmniRig to the very minimum (slowest possible) to
>prevent overloading the control channel between Router and the MK II.
>
>73,
>
>   ... Joe Subich, W4TV
>       microHAM America
>      http://www.microHAM-USA.com
>      http://groups.yahoo.com/group/microHAM
>
>       support e-mail:  support at microHAM.com
>
>
>On 6/22/2013 8:01 AM, f6gnz wrote:
>> I have updated my shack with an SDR which I want to use for reception only and keep my existing MK2, FT1000MP+ IC706 (for 50 MHz) for transmit only.
>> I can control SDR with HDSDR program and synchronize FT1000MP/IC706 frequencies/modes via the Omni-Rig program interfaced with HDSDR. This combination works perfectly, but now my DX4WIN becomes useless as it can't read nor control the radio, saying "ie_Open, device already open" and
>> "Could not open COM4 for keying, ie_Open, device already open" when I try to Start the Radio.
>> So, I can't log the QSOs with related radio data (mode, freq's) nor use spot clicks to set up the TX/RX frequencies, nor control my antenna rotator.
>> Is there any way to make the above combination work together???
>> Regards,
>> Radi F6GNZ
>>
>>
>>
>>
>> ------------------------------------
>>
>> This list is for the exchange of information about the use and operation of microHAM products.
>>
>> Anyone with specific hardware support issues should contact microHAM support at mailto:support at microHAM.com.
>>
>> Yahoo! Groups Links
>>
>> <*> To visit your group on the web, go to:
>>      http://groups.yahoo.com/group/microHAM/
>>
>> <*> Your email settings:
>>      Individual Email | Traditional
>>
>> <*> To change settings online go to:
>>      http://groups.yahoo.com/group/microHAM/join
>>      (Yahoo! ID required)
>>
>> <*> To change settings via email:
>>      microHAM-digest at yahoogroups.com
>>      microHAM-fullfeatured at yahoogroups.com
>>
>> <*> To unsubscribe from this group, send an email to:
>>      microHAM-unsubscribe at yahoogroups.com
>>
>> <*> Your use of Yahoo! Groups is subject to:
>>      http://docs.yahoo.com/info/terms/
>>
>>
>
>
>