[Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig

[Larry Gauthier (K8UT)]

If you have measured DX4Win polling at 500ms please describe how you are 
doing that. The last time I experimented with polling, any >Preferences 
setting below 2000ms was software-adjusted so that it never polled faster 
than every 2 seconds.

-larry (K8UT)
-----Original Message----- 
From: Radivoj Kar, F6GNZ
Sent: Monday, June 24, 2013 2:26 AM
To: Joe Subich, W4TV ; DX4WIN Refelector
Subject: Re: [Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig

Thanks Joe ! I have created an additional port for COM2 and set Omni-rig to 
this port with 1200 ms polling time (DX4WIN polls each 500ms). All works 
fine except when I select both Sync from Omni-Rig and Sync to Omni-rig to be 
able to set TX to RX-ed frequency but also to set RX frequency by clicking 
on the DX4WIN spots. In this case my IC706 starts to "walk" frequencies, 
like it had gone to the scanning mode....So, must chose only one way sync...

best 73, Radi F6GNZ





>________________________________
> De : "Joe Subich, W4TV" <lists at microham-usa.com>
>À : f6gnz <f6gnz at yahoo.com>; microham <microHAM at yahoogroups.com>
>Envoyé le : Samedi 22 juin 2013 15h02
>Objet : Re: [microHAM] MicroKeyer2,  DX4WIN, HDSDR and Omni-Rig
>
>
>
>If you are trying to configure a splitter function, you could try
>connecting HDSDR/OmniRig to Router's 2nd CAT port.  Otherwise, your
>logger developer will probably need to provide an OmniRig option
>where OmniRig serves both HDSRD and the logger.
>
>Note, if you use Router's 2nd CAT port, it will be necessary to set any
>polling from HDSDR/OmniRig to the very minimum (slowest possible) to
>prevent overloading the control channel between Router and the MK II.
>
>73,
>
>   ... Joe Subich, W4TV
>       microHAM America
>      http://www.microHAM-USA.com
>      http://groups.yahoo.com/group/microHAM
>
>       support e-mail:  support at microHAM.com
>
>
>On 6/22/2013 8:01 AM, f6gnz wrote:
>> I have updated my shack with an SDR which I want to use for reception 
>> only and keep my existing MK2, FT1000MP+ IC706 (for 50 MHz) for transmit 
>> only.
>> I can control SDR with HDSDR program and synchronize FT1000MP/IC706 
>> frequencies/modes via the Omni-Rig program interfaced with HDSDR. This 
>> combination works perfectly, but now my DX4WIN becomes useless as it 
>> can't read nor control the radio, saying "ie_Open, device already open" 
>> and
>> "Could not open COM4 for keying, ie_Open, device already open" when I try 
>> to Start the Radio.
>> So, I can't log the QSOs with related radio data (mode, freq's) nor use 
>> spot clicks to set up the TX/RX frequencies, nor control my antenna 
>> rotator.
>> Is there any way to make the above combination work together???
>> Regards,
>> Radi F6GNZ
>>
>>
>>
>>
>> ------------------------------------
>>
>> This list is for the exchange of information about the use and operation 
>> of microHAM products.
>>
>> Anyone with specific hardware support issues should contact microHAM 
>> support at mailto:support at microHAM.com.
>>
>> Yahoo! Groups Links
>>
>> <*> To visit your group on the web, go to:
>>      http://groups.yahoo.com/group/microHAM/
>>
>> <*> Your email settings:
>>      Individual Email | Traditional
>>
>> <*> To change settings online go to:
>>      http://groups.yahoo.com/group/microHAM/join
>>      (Yahoo! ID required)
>>
>> <*> To change settings via email:
>>      microHAM-digest at yahoogroups.com
>>      microHAM-fullfeatured at yahoogroups.com
>>
>> <*> To unsubscribe from this group, send an email to:
>>      microHAM-unsubscribe at yahoogroups.com
>>
>> <*> Your use of Yahoo! Groups is subject to:
>>      http://docs.yahoo.com/info/terms/
>>
>>
>
>
>
______________________________________________________________
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:DX4WIN at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html