[Boatanchors] [Glowbugs] Hot - melt glue on plastic ?

[Hal Dale]

Good stuff...use it all the time...Hal/WB4AEG
Sent using Zoho Mail






---- On Fri, 26 May 2017 17:47:08 -0400 Peter Loron <peterl at standingwave.org> wrote ----




Here ya go: 

 

https://www.amazon.com/E6000-230010-Craft-Adhesive-Ounces/dp/B007TSYNG8 

 

 

-Pete 

 

> On May 26, 2017, at 2:38 PM, Howie WA3MCK <wa3mck at gmail.com> wrote: 

> 

> Gang, 

> 

> What is this e6000 adhesive stuff everyone is talking about? 

> Do I need some? Obviously I do... where can I purchase it? 

> 

> Tnx es Happy Memorial Day 

> 

> de Howie WA3MCK 

> 

> 

> 

> 

> 

> 

> 

> On Friday, May 26, 2017, Gary MacGregor (KF5DZQ) <kf5dzq at gmail.com> wrote: 

> 

>> Steve 

>> What kind of cure time do you experience with e6000? 

>> 

>> In our hot humid atmosphere her in Corpus Christi, Texas it tacks up in a 

>> few minutes (depending on thickness), doesn't run. And is pretty much done 

>> in 10-15 minutes. I don't remember what full cure time is. But so far I 

>> haven't had to worry about that on projects. 

>> I love the forever weather proof and release when needed properties. And 

>> low to no vapors or residue. 

>> 

>> It should be perfect for his battery project. 

>> 

>> 73 

>> Gary MacGregor KF5DZQ 

>> 

>> Sent from my Stone & Chisel V 3.14 

>> 

>> On May 26, 2017 11:42 AM, "Steve WB6TNL" <sigcom at juno.com 

>> <javascript:_e(%7B%7D,'cvml','sigcom at juno.com');>> wrote: 

>> 

>>> Hot melt, using an adhesive formulated for adhesion to plastic or plastic 

>>> bonding, will work fine and cure almost immediately. 

>>> 3M has lots if info on this online. 

>>> 

>>> Finding a vendor for such adhesive may be the bigger problem whereas the 

>>> liquid adhesives (E6000, Goop, etc.) 

>>> are practically everywhere. I like these for their adhesive properties 

>>> but I don't like having to wait for them to cure. 

>>> 

>>> 73.......Steve Smith WB6TNL 

>>> "Snort Rosin" 

>>> 

>>> On Thursday, May 25, 2017 at 1:22:53 PM UTC-7, kargocult wrote: 

>>>> 

>>>> I have battery holder for the common 9 volt battery. I want to fasten to 

>>>> the 

>>>> 

>>>> backside of it, two small resistors for a voltage divider. My question 

>>>> is, will 

>>>> 

>>>> hot melt glue adhere to the plastic battery holder? If I rough it up a 

>>>> little with 

>>>> 

>>>> sandpaper ? As well as holding down the resistors, I want to cover up 

>>>> the 

>>>> 

>>>> bare wire connections. 

>>>> 

>>>> This is for a drop-in addition to old equipment, thus the odd-seeming 

>>>> 

>>>> construction. The question is maybe not so dumb as it seems, as I have 

>>>> found 

>>>> 

>>>> in the past that so-called superglue fails to hold on to most plastics. 

>>>> 

>>>> thanks- 

>>>> 

>>>> Hue 

>>>> 

>>> -- 

>>> -- 

>>> ZCZC 

>>> This is a transmission from the Glowbugs list 

>>> To unsubscribe from this group, send email to 

>>> tetrode+unsubscribe at googlegroups.com 

>>> <javascript:_e(%7B%7D,'cvml','tetrode%2Bunsubscribe at googlegroups.com');> 

>>> For more options, visit this group at 

>>> http://groups.google.com/group/tetrode?hl=en 

>>> NNNN 

>>> 

>>> --- 

>>> You received this message because you are subscribed to the Google Groups 

>>> "Glowbugs" group. 

>>> To unsubscribe from this group and stop receiving emails from it, send an 

>>> email to tetrode+unsubscribe at googlegroups.com 

>>> <javascript:_e(%7B%7D,'cvml','tetrode%2Bunsubscribe at googlegroups.com');>. 

>>> For more options, visit https://groups.google.com/d/optout. 

>>> 

>> -- 

>> -- 

>> ZCZC 

>> This is a transmission from the Glowbugs list 

>> To unsubscribe from this group, send email to 

>> tetrode+unsubscribe at googlegroups.com 

>> <javascript:_e(%7B%7D,'cvml','tetrode%2Bunsubscribe at googlegroups.com');> 

>> For more options, visit this group at 

>> http://groups.google.com/group/tetrode?hl=en 

>> NNNN 

>> 

>> --- 

>> You received this message because you are subscribed to the Google Groups 

>> "Glowbugs" group. 

>> To unsubscribe from this group and stop receiving emails from it, send an 

>> email to tetrode+unsubscribe at googlegroups.com 

>> <javascript:_e(%7B%7D,'cvml','tetrode%2Bunsubscribe at googlegroups.com');>. 

>> For more options, visit https://groups.google.com/d/optout. 

>> 

> ______________________________________________________________ 

> Boatanchors mailing list 

> Home: http://mailman.qth.net/mailman/listinfo/boatanchors 

> Help: http://mailman.qth.net/mmfaq.htm 

> Post: mailto:Boatanchors at mailman.qth.net 

> 

> List Administrator: Duane Fischer, W8DBF 

> ** For Assistance: dfischer at usol.com ** 

> 

> 

> This list hosted by: http://www.qsl.net 

> Please help support this email list: http://www.qsl.net/donate.html 

> 

 

______________________________________________________________ 

Boatanchors mailing list 

Home: http://mailman.qth.net/mailman/listinfo/boatanchors 

Help: http://mailman.qth.net/mmfaq.htm 

Post: mailto:Boatanchors at mailman.qth.net 

 

List Administrator: Duane Fischer, W8DBF 

** For Assistance: dfischer at usol.com ** 

 

 

This list hosted by: http://www.qsl.net 

Please help support this email list: http://www.qsl.net/donate.html