[TheForge] hydraulic chainsaws

[jerry Frost]

Sound advice Charles on all counts. Hydraulic tools are NOT meant to be hand held, even things like the jaws of life are supported mostly buy what they're cutting or spreading, not the EMT.

About problems with a Stihl chain saw. They don't care about alcohol in the fuel, you're just letting it sit too long. Alcohol is hydroscopic, it draws water from the air and water causes problems. If your chainsaw was full of gunk stop using cheap oil.

Buy gas one gallon at a time you can run a 345 Stihl full throttle for 8hrs on a gallon and you aren't doing near that. The tank holds less than a quart, mix the fuel one quart at a time and leave the gallon can SEALED. I have trouble believing you don't know how to operate 2 stroke tools properly.

Stop blaming the tools Terry it isn't their fault.

Frosty

-----Original Message-----
From: TheForge [mailto:theforge-bounces at mailman.qth.net] On Behalf Of Charles
Sent: Thursday, October 20, 2016 7:48 AM
To: terry l. ridder; Blacksmithing List Sponsored by ABANA
Subject: Re: [TheForge] hydraulic chainsaws

Hydraulic chainsaws are no fun either.  You have to have gear reduction on the motor or risk boiling on the fluid.  The hoses are heavy. Regarding twostroke chainsaws, no secrets.
1) Buy quality professional units.  Stihl, Huasky etc have homeowner lines and a professional lines. There is a big difference.  2) Have them tuned up by someone that knows what they are doing.  Every year.   3) Run them every day. 4) Only use quality fuel and oil additive and mix it per the instructions (no eyeballing)5) End of season run them dry with a preservative/fuel stabilizer added to the fuel. My son is a wild land firefighter.  This is what works for them.  Growing up with me, he had a different experience.  I  was too cheap for number 1 and 2 above and my circumstances did not lend themselves to number 3 though the rest I did follow.   So at forty years of age I turned my back on chainsaws and focused on keeping several good quality axes sharp, as well as several two man and one and a half man crosscut saws always sharp.  In my fifties now, I have a pro chainsaw, but still use the axe and saw almost exclusively.  I have an unusually large single bit Kelly that will throw chips the size of my fist when swung with skill and authority.   I teach scouts to fell trees by hand and they have proven many times (profitably for me) that two boys on a crosscut saw can buck a 12- 16 inch log before a forty year old dad can even get a chainsaw started many times now. Charles

 
      From: terry l. ridder <terrylr at blauedonau.com>
 To: theforge e-mail list <theforge at mailman.qth.net>
 Sent: Thursday, October 20, 2016 7:31 AM
 Subject: [TheForge] hydraulic chainsaws
   
hello;;

long time no write.

I am getting too  old to continue to fight with 2-cycle chainsaws.
i did learn my lesson about using gasoline with ethanol in it. the fuel lines were turned to a glob of rubber. The Stihl chainsaws just do not want to start for me.

i have seen several hydraulic chains. there are seeral used ones up for sale and I am considering one of them. Just hook it into the read hydaulics on the back of the tractor and start cutting.

I have several  dead chainsaws and figure it would worth asking if anyone had ever used the pieces of a gas chainsaw to build an hydraulic chainsaw. just a small hydraulic motor and a small trigger operated spool valve.

I would appreciate any hints or suggestions as to how to get gasoline chainsaws to start most of the time instead of none of the time.

--
terry l. ridder ><>
______________________________________________________________
TheForge mailing list
Home: http://mailman.qth.net/mailman/listinfo/theforge
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:TheForge at mailman.qth.net

TheForge mail list group photo site is
http://www.shutterfly.com
Login: blacksmithblacksmith at hotmail.com
Password: anvil

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message delivered to xlch58 at swbell.net


   
 
______________________________________________________________
TheForge mailing list
Home: http://mailman.qth.net/mailman/listinfo/theforge
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:TheForge at mailman.qth.net

TheForge mail list group photo site is
http://www.shutterfly.com
Login: blacksmithblacksmith at hotmail.com
Password: anvil

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message delivered to akfrosty at mtaonline.net