[TheForge] Drawing Down Bar Stock

[wmullett at bright.net]

A traditional strap hindge is thinned where it wraps around the barrel (pintle) then is lap welded back on itself for a couple of inches.  If this is what Ray is making, the whole stock is neither a uniform 1/2" or 1/4" but the resultant strap could be a uniform 1/2" from the barrel out or tapered from the barrel out.   Just depends on how much you would work the stock down after completing the weld.

Later strap hindges are full thickness around the barrel and double thickness where they overlap.

From: "roger olsen" <erik at methow.com>
Date: Mon May 8, 1:59 PM
To: "Sponsored by ABANA" <theforge at mailman.qth.net>
Subject: Re: [TheForge] Drawing Down Bar Stock

why not the whole hinge out of a hammered 1/4 x 2.  You are gaining nothing 
in strength if the hinge leaves the barrel at 1/4,  if anything you are 
loosing it by putting that much more weight out there for the barrels to 
support.  Seems a bit odd to me.



----- Original Message ----- 
From: <debmiller at fuse.net>
To: <munlaw2 at hcsmail.com>; "Sponsored by ABANA" <theforge at mailman.qth.net>
Sent: Monday, May 08, 2006 10:50 AM
Subject: RE: [TheForge] Drawing Down Bar Stock


> Hey Ron,
>
> I have to reproduce some "strap hinges" . The strap section is !/2 x 2 and 
> the section that would roll around the pin is 1/4 x 2.
>
> I figured that I need to hammer the width first then thin it out. Kevin 
> confirmed the approach. holding the width and thickness at the same time 
> could be fun!
>
> Ray
>
>
> ---- Ron Childers <munlaw2 at hcsmail.com> wrote:
>> Ray,
>>
>> What dimensions do you want? Off hand I'd say fuller then flatten the 
>> fuller
>> grooves, and keep your dimensions as you go..; or heat it and give it 
>> hell
>> w/ a power hammer. Overlap the blows in either case. Sounds like you're
>> going to make a hatchet.
>>
>> Ron Childers
>>
>> -----Original Message-----
>> From: theforge-bounces at mailman.qth.net
>> [mailto:theforge-bounces at mailman.qth.net] On Behalf Of debmiller at fuse.net
>> Sent: Monday, May 08, 2006 12:31 PM
>> To: Sponsored by ABANA
>> Cc: Chris Kilpatrick
>> Subject: [TheForge] Drawing Down Bar Stock
>>
>> Hi People!
>>
>> After all these years I come to realize I have never drawn rectangular 
>> bar
>> stock. Round, square, but not rectangular.
>>
>> I don't want to wast a bunch of material on trial and error for an urgent
>> project.
>>
>> The bar stock is 1/2" x 2".
>>
>> Hints?
>>
>>
>> Ray
>> Cincinnati
>> _______________________________________________
>> Manage membership or unsubscribe at:
>> http://mailman.qth.net/mailman/listinfo/theforge
>> theforge mail list group photo site is
>> http://www.photoaccess.com
>> Login:  blacksmithblacksmith at hotmail.com
>> password:  anvil
>> ___________
>>
>>
>>
>> _______________________________________________
>> Manage membership or unsubscribe at:
>> http://mailman.qth.net/mailman/listinfo/theforge
>> theforge mail list group photo site is
>> http://www.photoaccess.com
>> Login:  blacksmithblacksmith at hotmail.com
>> password:  anvil
>> ___________
>>
>>
>
> _______________________________________________
> Manage membership or unsubscribe at:
> http://mailman.qth.net/mailman/listinfo/theforge
> theforge mail list group photo site is
> http://www.photoaccess.com
> Login:  blacksmithblacksmith at hotmail.com
> password:  anvil
> ___________
>
> 

_______________________________________________
Manage membership or unsubscribe at:
http://mailman.qth.net/mailman/listinfo/theforge
theforge mail list group photo site is
http://www.photoaccess.com
Login:  blacksmithblacksmith at hotmail.com
password:  anvil
___________