[TheForge] Self contained hammer was a yak

Tue Nov 18 09:27:00 2003

That sounds like an excellent idea. Right now we still need to put paint 
and stalls inside the barn so the goats can move out of the garage.

Steve

Steve

Ralph Sproul wrote:
> We should get together this winter for a day of projects discussions.
> 
> Ralph
> ----- Original Message -----
> From: "Steve Smith" <[email protected]>
> To: <[email protected]>
> Sent: Monday, November 17, 2003 6:24 PM
> Subject: Re: [TheForge] Self contained hammer was a yak
> 
> 
> 
>>Yes, I'm headed along the Massey route that Frosty has discussed. I
>>think mine has a 40 pound ram. Right now I have the I beam column and
>>bottom anvil attached to the base plate. Most of the machining is done
>>on the ram and guide sleeve. So I'm pretty far along, just need to
>>develop some spare time to work on it again. We're just about dug out
>>from moving (or maybe we're going to quit for awhile!).
>>
>>Steve
>>
>>Ralph Sproul wrote:
>>
>>>        Steve,  Are you making a self contained air hammer?  I wasn't
> 
> aware
> 
>>>of this project if you were earlier.
>>>
>>>Ralph
>>>----- Original Message -----
>>>From: "Steve Smith" <[email protected]>
>>>To: <[email protected]>
>>>Sent: Sunday, November 16, 2003 7:49 AM
>>>Subject: Re: [TheForge] Self contained hammer was a yak
>>>
>>>
>>>
>>>
>>>>I had the same thought, Larry. I may already have this, but I'd like to
>>>>make sure I do!
>>>>
>>>>Is there life after moving? Maybe. We're not dug out yet (we moved from
>>>>Colorado to Maine last summer), but I'm starting to see the end of
>>>>catching up on all the maintenence the previous owner had let slide.
>>>>I'll probably have a life again by the end of the year. Then I can get
>>>>back to putting the air hammer pieces together, with lots of re-reading
>>>>of Frosy's notes.
>>>>
>>>>Steve Smith
>>>>
>>>>
>>>>Larry Brown wrote:
>>>>
>>>>
>>>>>Jerry,
>>>>>What did you finally come up with? You might have sent it to me but I
>>>>>had some computer problems and lost a lot of files.
>>>>>Larry Brown
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>><snip>
>>>>>>Valving and a short link crank connection mechanism.
>>>>>>
>>>>>>I wasn't satisfied with the Krause valving system and wanted something
>>>>>>that
>>>>>>generated less heat and wasn't generating compressed air while at
> 
> idle.
> 
>>>>>>Turned out to be Romper Room simple. <sigh>
>>>>>><snip>
>>>>>>
>>>>>>Frosty
>>>>>>------------------------
>>>>>>If it ain't forged
>>>>>>it ain't real.
>>>>>>Wrought iron is.
>>>>>>The FrostWorks
>>>>>>
>>>>>>Meadow Lakes, AK.
>>>>>
>>>>>
>>>>>_______________________________________________
>>>>>http://mailman.qth.net/mailman/listinfo/theforge
>>>>>theforge mail list group photo site is
>>>>>http://www.photoaccess.com
>>>>>Login:  [email protected]
>>>>>password:  anvil
>>>>>___________
>>>>>
>>>>>
>>>>>
>>>>
>>>>_______________________________________________
>>>>http://mailman.qth.net/mailman/listinfo/theforge
>>>>theforge mail list group photo site is
>>>>http://www.photoaccess.com
>>>>Login:  [email protected]
>>>>password:  anvil
>>>>___________
>>>>
>>>>
>>>
>>>
>>>_______________________________________________
>>>http://mailman.qth.net/mailman/listinfo/theforge
>>>theforge mail list group photo site is
>>>http://www.photoaccess.com
>>>Login:  [email protected]
>>>password:  anvil
>>>___________
>>>
>>>
>>>
>>
>>_______________________________________________
>>http://mailman.qth.net/mailman/listinfo/theforge
>>theforge mail list group photo site is
>>http://www.photoaccess.com
>>Login:  [email protected]
>>password:  anvil
>>___________
>>
>>
> 
> 
> _______________________________________________
> http://mailman.qth.net/mailman/listinfo/theforge
> theforge mail list group photo site is
> http://www.photoaccess.com
> Login:  [email protected]
> password:  anvil
> ___________
> 
> 
> 