[South Florida DX Association] How to work 3B9C : Rigs & Techniques

[bmarx@bellsouth.net]

I found this on their website and thought it good information for working all DX:
-Bill W2CQ

How to work 3B9C : Rigs & Techniques  http://www.fsdxa.com/3b9c/how-operating.html

Rigs and Operating Techniques
by Don, G3XTT

What about your transceiver?

The answer is that most transceivers these days are more than capable of doing the job, and almost all elderly ones are too. The
only feature you will need that you may not be using in your day-to-day ragchewing is split-frequency capability. 3B9C, like almost
all DXpeditions, will operate split-frequency at all times in the early parts of the expedition, though may revert to co-channel
working later, when the pile-ups diminish, for those without the capability. What is split-frequency operation, and why is it used?

Quite simply, DXpeditions transmit on one frequency and listen on a different frequency. For example they will transmit on 28.495MHz
and listen between 28.500 and 28.520MHz. There are two reasons:

1. If the DXpedition station listens on the frequency on which it is transmitting, it will not be heard by those calling because of
the pile-up on that frequency.

2. The DXpedition operator will be faced with a huge barrage of calls and will not be able to differentiate between them if they are
all calling on the same frequency.

Experienced DXpeditioners will tune slowly up and down their listening band. Listen to the stations working the DXpedition and
establish the operator�s tuning pattern. Work out where he is likely to be listening next and then call � bingo! Never, never
transmit on the DXpedition�s transmitting frequency unless the DXpedition says �Listening this frequency�.

On CW, generally all you will need to do is set your receiver to the 3B9C frequency and then use XIT (transmitter-incremental
tuning) to offset your transmitter by the necessary split (see your transceiver manual if you haven�t had occasion to do this
before). Activating RIT (receiver incremental tuning) will also allow you to hear the calling stations, while leaving your main
receive frequency on 3B9C.

RIT and XIT usually only work for splits of up to 10kHz, which may not be sufficient for SSB operation. In this case you need to
bring your second VFO into operation. Set, say, the A VFO on the 3B9C frequency. Set the B VFO on the frequency where 3B9C is
listening, and activate �Transmit on B, receive on A�. Again, your transceiver�s manual will explain how to do this.

When 3B9C responds to your call, the exchange will consist simply of an exchange of signal reports. Make sure the 3B9C operator also
has your callsign correct. The reason for the short, contest-style exchange is simple � the expedition operators want to maximize
the number of people who get a chance to work 3B9C, so contacts are kept as short as possible. Information such as QSL route, etc.
have been announced in this magazine and elsewhere, and there will even be a log lookup facility on the 3B9C Web Page so you can be
sure that you are in the log OK. If not, then do feel free to have a second attempt. If your contact is, indeed, OK, then please try
to work 3B9C on other bands and modes.

So where on the bands will you find 3B9C? The plan is to focus initially on the frequencies listed below, subject to change for
technical or operational reasons. In any case, the team is well aware that band plans in some countries, including the USA, restrict
certain classes of operator to sub-sections of the band. This will not only be reflected in the range of listening frequencies used,
but in transmitting frequencies as the DXpedition progresses. With widespread use of PacketCluster (via VHF/UHF and Internet) and
the DX Summit Web pages, even if you don�t hear 3B9C immediately, you should always be able to find out very easily where the
expedition is currently operating.

 Mhz CW SSB RTTY FM SSTV PSK
1.8 1822 1842 - - - -
3.5 3502 3795 3570 - - 3580
7 7002 7052 7035 - - 7037
10.1 10102 - 10137 - - 10140
14 14022 14195 14085 - 14230 14071
18 18072 18145 18100 - - 18100
21 21022 21295 21085 - - 21071
24.9 24892 24945 24920 - - 24920
28 28022 28495 28075 29580 - 28071
50 50102 50145 - - - -
50 Beacon 50090 - - - - -
Satellite  Look for us on OSCAR-40 (if it's working by then :-)
Moonbounce  70cm band and possibly 6m


Regarding the above frequencies, note that the team is aware of at least one other major DXpedition to be active while 3B9C is still
on the air, so may decide to change transmitting frequencies to avoid confusion. Typically, a DXpedition SSB station transmitting on
14.195 MHz will listen up in the range 14.200 to 14.220 MHz. If 3B9C finds itself operating on the same transmit frequency as
another DXpedition it will, for example, move down around 5kHz typically to 14.190 MHz and will then listen down say between 14.165
and 14.185 MHz so as to split the pile ups and avoid confusion.

Listen to the operator carefully. Each has been briefed to give the 3B9C callsign at least after every two QSOs and to announce the
listening frequencies every five QSOs. Incidentally, 3B9C will not work by numbers; believing that with good ears and equipment this
is quite unnecessary.

There really isn�t the space here to discuss how to get started with the more specialist bands and modes, but the team does
encourage readers to have a go. There have been many articles written about getting started on RTTY and PSK, which is
straightforward using a personal computer and its built-in sound card. There will be a section on the 3B9C Web site giving some
hints and tips, with links to useful references. The same is true of satellite and EME. The latter requires a well-equipped station,
but satellite operation through AO-40 doesn�t require large investments in equipment, especially if you already have a 70cm
multimode radio (3B9C will be using the popular FT-847) and 70cm Yagi. Again, follow the links on the Web page for suitable advice
on getting started.