[R-390] Re: R-390 Digest, Vol 4, Issue 6
Veenstra, Lester
lester.veenstra at lmco.com
Mon Aug 9 08:30:14 EDT 2004
Now that is a real receiver; Have one also, the FRR-59. Same "synthesis"
as the R-1230 as both are one of the last gasps of National Radio.
Les K1YCM/3 [former CTM1]
-----Original Message-----
From: r-390-bounces at mailman.qth.net
[mailto:r-390-bounces at mailman.qth.net] On Behalf Of Bernie Nicholson
Sent: Sunday, August 08, 2004 1:14 AM
To: r-390 at mailman.qth.net
Subject: [R-390] Re: R-390 Digest, Vol 4, Issue 6
Talking about better radios than the 390a ,Afew years ago I aquired a
WRR2 by national ,Now there is what I think is the penultimate Valve
reciever ,Sorry for you guys in the US ,TUBE reciever I would say that
it was a product of the early sixties and synthasized in 500 hz steps
and in 2 boxes that are both heavier than a 390a and also 2 channel
ISB capability also -, The biggest Radio reciever I have -owned was
made by the technical material corp and weighed in at more than
500pounds and also had a crystal controlled synthasizer and the radio
was capable of 4 channel ISB it completly filled a 7Ft rack and the
house lights used to dim when I turned it on. regards to everyone on
the site --- Original Message -----
From: <r-390-request at mailman.qth.net>
To: <r-390 at mailman.qth.net>
Sent: Sunday, August 08, 2004 12:40 PM
Subject: R-390 Digest, Vol 4, Issue 6
> Send R-390 mailing list submissions to
> r-390 at mailman.qth.net
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://mailman.qth.net/mailman/listinfo/r-390
> or, via email, send a message with subject or body 'help' to
> r-390-request at mailman.qth.net
>
> You can reach the person managing the list at
> r-390-owner at mailman.qth.net
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of R-390 digest..."
>
>
> Today's Topics:
>
> 1. Re: Ovens and Synchronization (Bob Camp)
> 2. Re: Halloween Set (Bob Camp)
> 3. Re: Halloween Set (Michael Murphy)
> 4. Re: Russian HF Radios (Bob Camp)
> 5. RE: Russian HF Radios (WF2U)
> 6. Birthday please (Richard May)
> 7. Re: Russian HF Radios (Bob Camp)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Sat, 07 Aug 2004 18:20:08 -0400
> From: Bob Camp <ham at cq.nu>
> Subject: Re: [R-390] Ovens and Synchronization
> To: Cecil Acuff <chacuff at cableone.net>, R-390 HF Receiver List
> <r-390 at mailman.qth.net>
> Message-ID: <F0AAD4FE-E8BF-11D8-917B-000A95C4FE54 at cq.nu>
> Content-Type: text/plain; charset=US-ASCII; format=flowed
>
> Hi
>
> The crystal ovens in the R-390 and the R1051 are different beasts. The
> 1051 oven standard is designed like a modern OCXO. The crystal inside
> it is cut so it is very stable at the oven operating point. The oven
> in the 1051 is designed so it is very temperature stable.
>
> Unfortunately none of this is true of the crystal oven in the R390
> series of radios. From talking to the guy who did the design of that
> part of the radio it was known to be a stop gap solution at the time.
> The main reason for it's inclusion was a requirement for modest
> stability at temperatures well below freezing.
>
> The crystal oven in the R390 swings in temperature over something like
> a 10 degree C range in normal operation. A fairly normal room should
> be stable within a degree or two for quite a while. Since the oven
> cycle time is in tens of minutes the oven is definitely a poor choice
> for basic temperature stability.
>
> The crystals in the R390 are not specifically cut for oven operation.
> This is a good thing since we don't turn the ovens on. In order to
> optimize them for an oven environment you cut the crystal so it's
> upper turn temperature is approximately at the oven temperature. Since
> there is a tolerance on the cutting process it is hard to do anything
> more than get them close to the oven temperature. When you cut the
> crystals this way a side effect is to make their performance at room
> temperature worse than a normal crystal.
>
> The oven on the PTO is kind of the same thing. It does not cycle over
> quite as wide a range as the crystal oven, but it does cycle further
> than your room probably does. The issue with the PTO is coil form
> shrink. The hotter you run the PTO the faster the master coil shrinks.
> Eventually the coil shrinks enough that you can no longer get the PTO
> on frequency with the correction adjustment. There is an article in
> Electric Radio back a few years that goes into all this stuff. Strange
> but true I worked for the guy who is quoted in the article. At the
> time I worked for him he would just barely admit working on the PTO's
> ....
>
> Finally, when you turn on the ovens on the R-390 you almost double the
> power in the radio. The oven in the R1051 is not as big a power hog as
> the ovens in the R390. When the heat in the radio goes up by that much
> the whole radio will get hotter. Unless you run some kind of fans to
> cool everything the result will be parts that run hot and wear out
> faster. Of course the fans would cool off the ovens which draws more
> power which heats up stuff more ... nasty cycle.
>
> One note - The ovens we are talking about are the ones on the crystal
> oscillator deck and inside the PTO. The plug in oven that has the
> calibrator crystal in it does not get turned off by the "oven on/off"
> switch. The plug in oven does do a good job, it does not pull a lot of
> power and it should be left running.
>
> One of the neat things you can do with a bunch of R390's (like say you
> just picked up a dozen of them ...) is to sort the crystals in the
> crystal oscillator deck. The closer you get to a matched set of
> crystals the less you will have to adjust the radio each time you
> change bands. I still think they should have put tuning caps on the
> crystals. The reason they didn't : " Well we didn't do it because it
> wasn't in the spec". Darn Ft. Monmouth.
>
> Take Care!
>
> Bob Camp
> KB8TQ
>
>
>
> On Aug 7, 2004, at 5:14 PM, Cecil Acuff wrote:
>
> > Hey guys,
> >
> > Lets talk about the crystal ovens in the 390A. I seem to
> > remember it is common practice to not use them anymore for the sake
> > of longevity.
> >
> > My R-1051 experience is that one can't do without the oven in the
> > Frequency Standard because without the oven the stability the 1051
> > is known for goes
> > down the toilet. The crystal in the oven was designed to work at a
> > specific
> > temp to be stabile. There is a nice flat spot in the curve up
around
> > 85C
> >
> > Is this not the same with the crystal deck, calibrator xtals and
> > maybe to a lesser degree the PTO in the 390A?
> >
> > Looking in the Y2K manual it seems recommended to fire them up a few
> > hours before an alignment but then go back to the practice of
> > turning them off for
> > our day to day ops....seems that would negate the alignment.
Wouldn't
> > one
> > be better off doing the alignments in the state one would normally
> > operate
> > the radio?
> >
> > I am at the point in my R-390A ownership that I am starting to get
> > technical with the 390A now that time presents that opportunity. As
> > a result I guess
> > I'll be asking some of the typical beginner questions.
> >
> > Coming to a post near you: How does one go about putting a radio
> > back together where everything is totally out of mechanical and
> > electrical sync!
> >
> > I pulled the whole IF deck apart for complete cleaning....4 years
> > ago. No problem on getting everything back together just need some
> > starting point
> > for getting everything re-synchronized. It was a nasty blue
> > striper...won't
> > know it once it's complete....it cleaned up very nicely. The gear
> > train is
> > separated from the IF deck chassis and all that is separated from
the
> > xtal
> > deck.
> >
> > Gear train works like a swiss watch....love that Mobil 1
> >
> > Thanks in advance!
> >
> > Cecil Acuff
> >
> >
> > ______________________________________________________________
> > R-390 mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/r-390
> > Help: http://mailman.qth.net/faq.htm
> > Post: mailto:R-390 at mailman.qth.net
> > Unsubscribe: http://mailman.qth.net/mailman/options/r-390
> >
>
>
>
> ------------------------------
>
> Message: 2
> Date: Sat, 07 Aug 2004 18:33:31 -0400
> From: Bob Camp <ham at cq.nu>
> Subject: Re: [R-390] Halloween Set
> To: Commtekman at aol.com, R-390 HF Receiver List <r-390 at mailman.qth.net>
> Message-ID: <CF360A9F-E8C1-11D8-917B-000A95C4FE54 at cq.nu>
> Content-Type: text/plain; charset=US-ASCII; format=flowed
>
> Hi
>
> Main power to the radio is controlled by a microswitch ganged to the
> function switch shaft. It is fairly common for this little item to
> weld it's self in the on position. Last time I had a problem with one
> of these I got the parts from somebody on the list. It was either
> David Medley or Hank. The fix is not to hard except you have to
> unmount the front panel to get at the switch. It's a little time
> consuming is all. When you mount the new one you want to make sure
> it's snug on the mount so it goes full on / full off. If it gets loose
> it may weld again.
>
> The flashing is a bit odd. Other than the heater thermostat in the
> crystal oven I can't think of anything in the pilot light circuit that
> would cycle. You may have a bad wire from the power transformer to the
> filaments. It's P111 / J111 in the Y2K manual. You might also make
> sure the "ovens" switch on the back of the radio is set to off.
>
> Everything about these radios is fixable. I do not know of any parts
> that are in the "can't get or replace them" category. Dive on in and
> see what's wrong. They were designed to be repaired.
>
> Enjoy!
>
> Bob Camp
> KB8TQ
>
>
>
> On Aug 7, 2004, at 5:42 PM, Commtekman at aol.com wrote:
>
> > Hey Guys-
> > In one of my 'senior moments', I bought an R-390 off of Eplace,
> > finally received it, powered it up without turning it on, all the
> > tube filaments came on while it was still in the 'off' position, and
> > the dial light started flashing
> > like a haunted house on halloween night. I suspect without going
> > further that
> > this has something to do with the standby or break-in being held up
> > and not
> > releasing. Ideas?
> > Tnx Bob
> > K6OSM
> > Mccall, Idaho
> > ______________________________________________________________
> > R-390 mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/r-390
> > Help: http://mailman.qth.net/faq.htm
> > Post: mailto:R-390 at mailman.qth.net
> > Unsubscribe: http://mailman.qth.net/mailman/options/r-390
> >
>
>
>
> ------------------------------
>
> Message: 3
> Date: Sat, 7 Aug 2004 18:41:56 -0400
> From: "Michael Murphy" <mjmurphy45 at comcast.net>
> Subject: Re: [R-390] Halloween Set
> To: "Bob Camp" <ham at cq.nu>, <Commtekman at aol.com>, "R-390 HF Receiver
> List" <r-390 at mailman.qth.net>
> Message-ID: <003501c47ccf$be69dd60$6600a8c0 at comcast.net>
> Content-Type: text/plain; charset="iso-8859-1"
>
> No Bob, Don't get going on the micro switch! That could be worse than
> the ballast blast. Mike WB2UID
>
> ----- Original Message -----
> From: "Bob Camp" <ham at cq.nu>
> To: <Commtekman at aol.com>; "R-390 HF Receiver List"
> <r-390 at mailman.qth.net>
> Sent: Saturday, August 07, 2004 6:33 PM
> Subject: Re: [R-390] Halloween Set
>
>
> > Hi
> >
> > Main power to the radio is controlled by a microswitch ganged to the
> > function switch shaft. It is fairly common for this little item to
> > weld it's self in the on position. Last time I had a problem with
> > one of these I got the parts from somebody on the list. It was
> > either David Medley or Hank. The fix is not to hard except you have
> > to unmount the front panel to get at the switch. It's a little time
> > consuming is all. When you mount the new one you want to make sure
> > it's snug on the mount so it goes full on / full off. If it gets
> > loose it may weld again.
> >
> > The flashing is a bit odd. Other than the heater thermostat in the
> > crystal oven I can't think of anything in the pilot light circuit
> > that would cycle. You may have a bad wire from the power transformer
> > to the filaments. It's P111 / J111 in the Y2K manual. You might also
> > make sure the "ovens" switch on the back of the radio is set to off.
> >
> > Everything about these radios is fixable. I do not know of any parts
> > that are in the "can't get or replace them" category. Dive on in and
> > see what's wrong. They were designed to be repaired.
> >
> > Enjoy!
> >
> > Bob Camp
> > KB8TQ
> >
> >
> >
> > On Aug 7, 2004, at 5:42 PM, Commtekman at aol.com wrote:
> >
> > > Hey Guys-
> > > In one of my 'senior moments', I bought an R-390 off of Eplace,
finally
> > > received it, powered it up without turning it on, all the tube
> > > filaments came on while it was still in the 'off' position, and
> > > the dial light started flashing
> > > like a haunted house on halloween night. I suspect without going
> > > further that
> > > this has something to do with the standby or break-in being held
up
> > > and not
> > > releasing. Ideas?
> > > Tnx Bob
> > > K6OSM
> > > Mccall, Idaho
> > > ______________________________________________________________
> > > R-390 mailing list
> > > Home: http://mailman.qth.net/mailman/listinfo/r-390
> > > Help: http://mailman.qth.net/faq.htm
> > > Post: mailto:R-390 at mailman.qth.net
> > > Unsubscribe: http://mailman.qth.net/mailman/options/r-390
> > >
> >
> > ______________________________________________________________
> > R-390 mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/r-390
> > Help: http://mailman.qth.net/faq.htm
> > Post: mailto:R-390 at mailman.qth.net
> > Unsubscribe: http://mailman.qth.net/mailman/options/r-390
>
>
>
>
> ------------------------------
>
> Message: 4
> Date: Sat, 07 Aug 2004 19:25:17 -0400
> From: Bob Camp <ham at cq.nu>
> Subject: Re: [R-390] Russian HF Radios
> To: Forrest Myers <femyers01 at bellsouth.net>, R-390 HF Receiver List
> <r-390 at mailman.qth.net>
> Message-ID: <0AA50B0E-E8C9-11D8-917B-000A95C4FE54 at cq.nu>
> Content-Type: text/plain; charset=US-ASCII; format=flowed
>
> Hi
>
> Well I seem to remember they made a receiver called the R320 that was
> intended as a dedicated intercept radio. I have been able to find very
> little information on the radio and have never seen one. What little I
> was able to find claims it was a bit large (a couple hundred pounds)
> but worked quite well.
>
> Enjoy!
>
> Bob Camp
> KB8TQ
>
>
> On Aug 7, 2004, at 5:59 PM, Forrest Myers wrote:
>
> > Well,
> > If the Russians copied an r-390 non A they may have made a better
all
> > tube
> > hf radio than the r390-a, hee hee.
> >
> > Forrest Myers
> > AG4ND
> >
> >
>
>
>
> ------------------------------
>
> Message: 5
> Date: Sat, 7 Aug 2004 22:01:12 -0400
> From: "WF2U" <wf2u at starband.net>
> Subject: RE: [R-390] Russian HF Radios
> To: "Bob Camp" <ham at cq.nu>, "Cecil Acuff" <chacuff at cableone.net>,
> "R-390 HF Receiver List" <r-390 at mailman.qth.net>
> Message-ID: <NABBLNEJDDKECLKHCAAPGEGBKFAA.wf2u at starband.net>
> Content-Type: text/plain; charset="iso-8859-1"
>
> The Russians indeed built a receiver in the same class and purpose as
the
> R-390 and R-390A. The frequency display was not the Veeder-Root
> mechanical-digital counter as in the R-390* series, but an analog
system
> comprised of a coarse dial displaying each 2 MHz band in 100 KHz
increments
> and a "fine" frequency dial which was projected from the rear,
displaying
> increments of 1 KHz, above the coarse dial. The receiver has a dual
> conversion system based on a tunable first IF of 1.5 to 3.5 MHz,
mixed
down
> to the 215 KHz fixed IF. The rest of the bands are converted with a
crystal
> oscillator/mixer to the variable IF, a la Collins. The difference is
that
> the bands are 2 MHz wide instead of the 1 MHz in the Collins system,
and
the
> tuning is not a permeability tuning arrangement with slugs moving in
and
out
> of the coils, but a multi-section main tuning capacitor and a drum
> bandswitch system. The selectivity is infinitely adjustable (by
variable
> coupling of the 215 KHz IF stages, between 1 KHz and 14 KHz, and an
audio
> bandpass filter is provided as well, selectable between 8, 5, 2.5 and
0.3
> KHz.
> The receiver contains a thermostat-controlled ovenized crystal
calibrator,
> the BFO is tuned with a reduction drive, with a dial displaying -5
KHz -
> 0 - +5 KHz frequency in 100 Hz increments. AGC time constants
available
are
> 1, 0.1 and 0.05 seconds or AGC OFF.
> The RF input is selectable with a front panel switch between a 60 to
400
> ohm (nominal), balanced and unbalanced dipole, whip/long wire or
ground,
> antenna trimmer control on the front panel.
> There are jacks for AGC in/out for diversity, 1st and 2nd IF out, and
600
> ohm audio line out (besides the headphone jacks).
> The construction is modular: the RF/first IF/crystal oscillator/mixer
is
in
> the bottom drawer in the cabinet, the top drawer contains the second
IF,
> BFO, AGC, detector and audio circuits, as well as the metering circuit
-
the
> receiver has a built-in emission tester and each tube can be selected
for
> test while the receiver is in operation, or the meter can be switched
by
the
> selector to monitor the audio line output or the received signal
strength.
> The power supply is external, and interestingly the input is
selectable
> between 220 and 120 VAC...
>
> The first version of this receiver was put in service with the
(former)
> Soviet Armed Forces in 1948 with the military nomenclature of R-250
> ("Whale"), and the improved version, the R-250M was issued in the
early
> 1950's. Both these models used standard metal octal tube types, which
are
> equivalent to the US types. In the early 60's the receiver was
modernized
> and standard miniature tubes were used together with some circuit
> improvements. The self testing arrangement got an additional feature,
a
> built-in noise generator, so besides emission testing of the tubes, a
> sensitivity check could be performed without external test equipment
(like:
> "Hey, Sergey, I can't copy headquarters!" "Check the receiver with
the
> noise generator, Ivan!" "click, click, click as the meter switch is
turned
> to check each tube, and the input with the noise generator"- "There is
> nothing wrong with the receiver" "S**t! The ice broke the antenna
again!")
> This version was the R-250M2 and was in production until 1981.
>
> Incidentally, in all these receivers the B+ is 160 VDC, giving the
tubes a
> real long and cool life, with a total current draw of 120 mA! The
> filaments are series-parallel connected (all 6.3 V tubes) for 12.6 V
at 6
A.
>
> I own a pristine R-250M model. Its performance is simply incredible,
> considering an early 50's design with all octal tubes (19 of them). It
> outperforms many receivers 10 years more advanced. The spec on the
> sensitivity is 0.6 uV for S/N ratio of 10 dB at 3 KHz IF and 2.5 KHz
AF
> bandwidth, with a 100 ohm antenna. Audio output is 0.5 W into 600 ohms
at
4%
> (AF output tube is a Russian 6P6, which is the exact equivalent of the
6V6).
> Frequency stability is specified as maximum 200 Hz drift after a
warm-up
of
> 2 hours!
> The tube complement in US equivalent designations is 10 x 6SK7, 3 x
6AC7,
> 3 x 6SA7, 2 x 6H6, 1 x 6V6, + a voltage regulator tube (I have to find
the
> US equivalent) and the power supply has a 5Z4 rectifier.
> The detector/BFO injection is good enough for good SSB reception, even
with
> the AGC on, as well as CW is just great to copy on it with all the
> selectivity options.
> It's no slouch in AM quality, although .5 W is really not enough to
drive
> a big speaker without an outboard amp.
>
> All this in a real "boatanchor" package of 26" wide, 18" deep and 21"
tall
> (with the shock mounts), weighing 209 pounds, without the power
supply,
> which weighs about 35 pounds.
> Options available were RTTY demodulator, high precision AFC (Automatic
> Frequency Control) system, which provides tuning with a servo motor
and a
> diversity control interface. There was also a vibrator power supply
option,
> for 12 VDC input.
>
> Construction is really excellent quality and it looks like good US
mil-spec
> work. The wiring and soldering are also first-class, the components
look
> high quality. The transformers are potted, cased and painted, just
like
the
> US mil. stuff. Incidentally, I got a couple of sets of NOS spare
tubes,
with
> 1972 manufacturing date. Pretty late for still making metal octal
military
> tubes!
>
> There are photos of the various versions at a Russian web site
> http://www.cqham.ru/trx/r_250.html .
>
> Well, I hope this wasn't boring, but there is not too much traffic
here
> tonight anyway...
>
> 73, Meir WF2U
> Gowensville, SC
>
>
> -----Original Message-----
> From: r-390-bounces at mailman.qth.net
[mailto:r-390-bounces at mailman.qth.net]
> On Behalf Of Bob Camp
> Sent: Saturday, August 07, 2004 5:15 PM
> To: Cecil Acuff; R-390 HF Receiver List
> Subject: [R-390] Russian HF Radios
>
> Hi
>
> Well obviously we need to get something going.
>
> How about did the Russians build a better all tube HF receiver than
the
> R-390A? From what I hear the answer may be yes ....
>
> That's the way to see if anybody's listening.
>
> Enjoy!
>
> Bob Camp
> KB8TQ
>
>
> On Aug 7, 2004, at 4:57 PM, Cecil Acuff wrote:
>
> > Test...
> >
> > ______________________________________________________________
> > R-390 mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/r-390
> > Help: http://mailman.qth.net/faq.htm
> > Post: mailto:R-390 at mailman.qth.net
> > Unsubscribe: http://mailman.qth.net/mailman/options/r-390
> >
>
> ______________________________________________________________
> R-390 mailing list
> Home: http://mailman.qth.net/mailman/listinfo/r-390
> Help: http://mailman.qth.net/faq.htm
> Post: mailto:R-390 at mailman.qth.net
> Unsubscribe: http://mailman.qth.net/mailman/options/r-390
>
>
>
> ------------------------------
>
> Message: 6
> Date: Sun, 8 Aug 2004 02:02:47 +0000 (GMT)
> From: Richard May <richardmay at hotmail.com>
> Subject: [R-390] Birthday please
> To: r-390 at mailman.qth.net
> Message-ID: <9762922.1091930567453.JavaMail.Administrator at win02>
> Content-Type: text/plain; charset=us-ascii
>
> Hi
>
> Click on the link below and please enter your birthday for me. It will
take less than 1 minute. I am creating a birthday list of all my friends
and
family.
>
> http://www.BirthdayAlarm.com/dob2/21710769a384025368b142965556c904
>
> Many thanks
> Richard
>
>
>
> ------------------------------
>
> Message: 7
> Date: Sat, 07 Aug 2004 22:37:46 -0400
> From: Bob Camp <ham at cq.nu>
> Subject: Re: [R-390] Russian HF Radios
> To: wf2u at starband.net, wf2u at starband.net, R-390 HF Receiver List
> <r-390 at mailman.qth.net>
> Message-ID: <EED294CD-E8E3-11D8-917B-000A95C4FE54 at cq.nu>
> Content-Type: text/plain; charset=US-ASCII; format=flowed
>
> Hi
>
> So how do you get one of these beasts?
>
> Obviously we need more R390 to R250M2 comparisons.
>
> Take Care!
>
> Bob Camp
> KB8TQ
>
>
> On Aug 7, 2004, at 10:01 PM, WF2U wrote:
>
> > The Russians indeed built a receiver in the same class and purpose
as
> > the
> > R-390 and R-390A. The frequency display was not the Veeder-Root
> > mechanical-digital counter as in the R-390* series, but an analog
> > system
> > comprised of a coarse dial displaying each 2 MHz band in 100 KHz
> > increments
> > and a "fine" frequency dial which was projected from the rear,
> > displaying
> > increments of 1 KHz, above the coarse dial. The receiver has a
dual
> > conversion system based on a tunable first IF of 1.5 to 3.5 MHz,
> > mixed down
> > to the 215 KHz fixed IF. The rest of the bands are converted with a
> > crystal
> > oscillator/mixer to the variable IF, a la Collins. The difference is
> > that
> > the bands are 2 MHz wide instead of the 1 MHz in the Collins system,
> > and the
> > tuning is not a permeability tuning arrangement with slugs moving in
> > and out
> > of the coils, but a multi-section main tuning capacitor and a drum
> > bandswitch system. The selectivity is infinitely adjustable (by
> > variable
> > coupling of the 215 KHz IF stages, between 1 KHz and 14 KHz, and an
> > audio
> > bandpass filter is provided as well, selectable between 8, 5, 2.5
and
> > 0.3
> > KHz.
> > The receiver contains a thermostat-controlled ovenized crystal
> > calibrator,
> > the BFO is tuned with a reduction drive, with a dial displaying -5
> > KHz -
> > 0 - +5 KHz frequency in 100 Hz increments. AGC time constants
> > available are
> > 1, 0.1 and 0.05 seconds or AGC OFF.
> > The RF input is selectable with a front panel switch between a 60
to
> > 400
> > ohm (nominal), balanced and unbalanced dipole, whip/long wire or
> > ground,
> > antenna trimmer control on the front panel.
> > There are jacks for AGC in/out for diversity, 1st and 2nd IF out,
and
> > 600
> > ohm audio line out (besides the headphone jacks).
> > The construction is modular: the RF/first IF/crystal
oscillator/mixer
> > is in
> > the bottom drawer in the cabinet, the top drawer contains the second
> > IF,
> > BFO, AGC, detector and audio circuits, as well as the metering
circuit
> > - the
> > receiver has a built-in emission tester and each tube can be
selected
> > for
> > test while the receiver is in operation, or the meter can be
switched
> > by the
> > selector to monitor the audio line output or the received signal
> > strength.
> > The power supply is external, and interestingly the input is
selectable
> > between 220 and 120 VAC...
> >
> > The first version of this receiver was put in service with the
(former)
> > Soviet Armed Forces in 1948 with the military nomenclature of R-250
> > ("Whale"), and the improved version, the R-250M was issued in the
early
> > 1950's. Both these models used standard metal octal tube types,
which
> > are
> > equivalent to the US types. In the early 60's the receiver was
> > modernized
> > and standard miniature tubes were used together with some circuit
> > improvements. The self testing arrangement got an additional
feature, a
> > built-in noise generator, so besides emission testing of the tubes,
a
> > sensitivity check could be performed without external test equipment
> > (like:
> > "Hey, Sergey, I can't copy headquarters!" "Check the receiver with
the
> > noise generator, Ivan!" "click, click, click as the meter switch is
> > turned
> > to check each tube, and the input with the noise generator"- "There
is
> > nothing wrong with the receiver" "S**t! The ice broke the antenna
> > again!")
> > This version was the R-250M2 and was in production until 1981.
> >
> > Incidentally, in all these receivers the B+ is 160 VDC, giving the
> > tubes a
> > real long and cool life, with a total current draw of 120 mA! The
> > filaments are series-parallel connected (all 6.3 V tubes) for 12.6 V
> > at 6 A.
> >
> > I own a pristine R-250M model. Its performance is simply incredible,
> > considering an early 50's design with all octal tubes (19 of them).
It
> > outperforms many receivers 10 years more advanced. The spec on the
> > sensitivity is 0.6 uV for S/N ratio of 10 dB at 3 KHz IF and 2.5
KHz
> > AF
> > bandwidth, with a 100 ohm antenna. Audio output is 0.5 W into 600
ohms
> > at 4%
> > (AF output tube is a Russian 6P6, which is the exact equivalent of
the
> > 6V6).
> > Frequency stability is specified as maximum 200 Hz drift after a
> > warm-up of
> > 2 hours!
> > The tube complement in US equivalent designations is 10 x 6SK7, 3 x
> > 6AC7,
> > 3 x 6SA7, 2 x 6H6, 1 x 6V6, + a voltage regulator tube (I have to
find
> > the
> > US equivalent) and the power supply has a 5Z4 rectifier.
> > The detector/BFO injection is good enough for good SSB reception,
even
> > with
> > the AGC on, as well as CW is just great to copy on it with all the
> > selectivity options.
> > It's no slouch in AM quality, although .5 W is really not enough
to
> > drive
> > a big speaker without an outboard amp.
> >
> > All this in a real "boatanchor" package of 26" wide, 18" deep and
21"
> > tall
> > (with the shock mounts), weighing 209 pounds, without the power
supply,
> > which weighs about 35 pounds.
> > Options available were RTTY demodulator, high precision AFC
(Automatic
> > Frequency Control) system, which provides tuning with a servo motor
> > and a
> > diversity control interface. There was also a vibrator power supply
> > option,
> > for 12 VDC input.
> >
> > Construction is really excellent quality and it looks like good US
> > mil-spec
> > work. The wiring and soldering are also first-class, the components
> > look
> > high quality. The transformers are potted, cased and painted, just
> > like the
> > US mil. stuff. Incidentally, I got a couple of sets of NOS spare
> > tubes, with
> > 1972 manufacturing date. Pretty late for still making metal octal
> > military
> > tubes!
> >
> > There are photos of the various versions at a Russian web site
> > http://www.cqham.ru/trx/r_250.html .
> >
> > Well, I hope this wasn't boring, but there is not too much traffic
here
> > tonight anyway...
> >
> > 73, Meir WF2U
> > Gowensville, SC
> >
> >
> > -----Original Message-----
> > From: r-390-bounces at mailman.qth.net
> > [mailto:r-390-bounces at mailman.qth.net]
> > On Behalf Of Bob Camp
> > Sent: Saturday, August 07, 2004 5:15 PM
> > To: Cecil Acuff; R-390 HF Receiver List
> > Subject: [R-390] Russian HF Radios
> >
> > Hi
> >
> > Well obviously we need to get something going.
> >
> > How about did the Russians build a better all tube HF receiver than
the
> > R-390A? From what I hear the answer may be yes ....
> >
> > That's the way to see if anybody's listening.
> >
> > Enjoy!
> >
> > Bob Camp
> > KB8TQ
> >
> >
> > On Aug 7, 2004, at 4:57 PM, Cecil Acuff wrote:
> >
> >> Test...
> >>
> >> ______________________________________________________________
> >> R-390 mailing list
> >> Home: http://mailman.qth.net/mailman/listinfo/r-390
> >> Help: http://mailman.qth.net/faq.htm
> >> Post: mailto:R-390 at mailman.qth.net
> >> Unsubscribe: http://mailman.qth.net/mailman/options/r-390
> >>
> >
> > ______________________________________________________________
> > R-390 mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/r-390
> > Help: http://mailman.qth.net/faq.htm
> > Post: mailto:R-390 at mailman.qth.net
> > Unsubscribe: http://mailman.qth.net/mailman/options/r-390
> >
>
>
>
> ------------------------------
>
> _______________________________________________
> R-390 mailing list
> R-390 at mailman.qth.net
> http://mailman.qth.net/mailman/listinfo/r-390
>
>
> End of R-390 Digest, Vol 4, Issue 6
> ***********************************
______________________________________________________________
R-390 mailing list
Home: http://mailman.qth.net/mailman/listinfo/r-390
Help: http://mailman.qth.net/faq.htm
Post: mailto:R-390 at mailman.qth.net
Unsubscribe: http://mailman.qth.net/mailman/options/r-390
More information about the R-390
mailing list