[Pro2006] pro-2006 Fading backlight problem?

Tue, 11 Jun 2002 22:15:52 -0400

Hello Len

Just installing a new motherboard and cpu, and writing emails in between, and
chewing gum at the same time. Now to get technical Microstar K7T266 PRO-RU
mainboard with an Athlon XP 1800 ghz processor, It actually booted up fist time,
all systems were good, so I thought I would get fancy and overclock it a bit,
bad move had to clear the CMOS, and still couldn't get it to boot took out all
the cables and re-installed them etc etc etc kicked the dog several times
shouted at the wife and kids drank several beers, finally just got it to boot up
again. looking good now, checked the date and time with "atomtime" so it should
be OK now.

Mel
----- Original Message -----
From: "Len G. Carpenter" <[email protected]>
To: <[email protected]>
Sent: Tuesday, June 11, 2002 8:57 PM
Subject: Re: [Pro2006] pro-2006 Fading backlight problem?

> Hey Mel,
>
> Check your you date settings, your message says you have it set to April 24
2002
>
> Mel wrote:
>
> > Hey Len
> >
> > > Just remember that your computer is now your scanner, if no computer then
you
> > > can't scan what you have programmed into it.
> >
> > You can't scan the Frequencies you have programmed into the computer
software
> > that runs the scanner, but you can still input the very same frequencies up
to
> > 400 of course, and scan them. Don't confuse people.
> >
>
> I was not trying to confuse anyone, as I said above once you install that
board and
> use it and probe or whatever, you need the computer to continue scanning the
> channels that you have in probe or whatever other software you are going to
use.
>
> >
> > > It also will not program the
> > > channels in your scanner.
> >
> > Nobody said it would. When it is not connected to the computer it stills
> > operates like any other scanner and programing is done the same way as any
other
> > scanner.
> >
>
> That's what I was trying to say it will not program the channels in the
scanner,
> with all the new scanners out there that have computer control people need to
> realize that this add on board will not program the channels in the scanner.
> Sure it will work just fine without it but it will not scan the channels that
you
> have in probe or whatever other software you are using.
>
> >
> > > Lots of people do not realize this, great idea as
> > > long as you can have a computer with the scanner all the time.
> >
> > Len you do not need a computer to use the Pro-2006. You do not need a
computer
> > with the radio all the time. Why are you saying this.
> >
>
> I am saying that if you install an OS456 board of any type in the scanner and
then
> load lots of channels into probe or whatever other software you are using that
when
> you no longer have the computer hooked to the scanner you can no longer scan
all
> those channels, correct me if I am wrong but as far as I know they have not
made any
> changes to the OS456 boards to allow them to program the memory in the
scanner.
>
> >
> > >  Then the problem
> > > is find decent software for it.
>
> > The Probe software for the 2006 is excellent, check the reviews, ask the
> > hundreds that use it. ScanStar Deluxe is another excellent software program
to
> > use. These aren't decent software programs your right there Len there
excellent
> > programs.
> >
>
> Never said that there was anything wrong with probe or scanstar, I have never
used
> it so I cannot be sure whats what with it, just go by what I have read in the
> newsgroups.
>
> >
> > Now the other route to go is to use the CE232 Board and Pro-Turbo software
> > nothing wrong with that either.
> >
> > Mel
> >
> > ---
> > Outgoing mail is certified Virus Free.
> > Checked by AVG anti-virus system (http://www.grisoft.com).
> > Version: 6.0.370 / Virus Database: 205 - Release Date: 05/06/2002
> >
> > _______________________________________________
> > Pro2006 mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/pro2006
>
> _______________________________________________
> Pro2006 mailing list
> [email protected]
> http://mailman.qth.net/mailman/listinfo/pro2006

---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.370 / Virus Database: 205 - Release Date: 05/06/2002