[OKDXA] Gary - Parts for Hexbeam

[Jeff Martin]

Gary,

  I have a KIO Hexbeam in my DXpedition snowboard bag. The small spreader 
section is 1/2 inch diameter, the medium spreader section is 3/4 inch 
diameter, and the large spreader section is 1 inch diameter. The 
instuction sheet doesn't say the lengths, but I could go pull the pieces 
out of the bag and measure them if you like...

73,
Jeff - K5WE

------ Original Message ------
>From garylm at kiamichiwb.org
To "OKDXA" <okdxa at mailman.qth.net>
Date 1/25/2023 11:21:19 PM
Subject Re: [OKDXA] Gary - Parts for Hexbeam

>
>
>
>THANK BOTH OF YOU FOR YOUR HELP. I'M NOT SURE WHAT SIZE THE SPREADERS ARE, THERE ARE THREE SECTIONS PER SPREADER.  THIS WOULD HAPPEN WHEN THE 3Y IS COMING UP, WOULD BE ATNO FOR ME DOWN HERE.
>I HAVE HAD THE K4KIO HEX-BEAM ABOUT 3 OR 4 YEARS AND THIS IS FIRST PROBLEM.
>I STILL HAVE GROUND MOUNTED 43FT VERTICAL I CAN USE WITH TUNER.  CHECKED IT THIS EVENING AND SEAMED TO TUNE OK ON 10 THRU 40M, BUT ONLY HAVE ABOUT 5 RADIALS DOWN AND MOUNTED ON 3 BY 4FT  1/2 INCH STILL PLATE.
>CANNOT DO ANYTHING WITH HEX-BEAM UNTIL GROUND DRYS OUT, TO SOFT TO GET LIFT IN TO IT.  GOING TO PUT IT UP TO AROUND 40FT AT SAME TIME, IT IS AT 23FT NOW.
>WILL GET IN TOUCH WITH YOU.
>73
>GARY - WQ5R
>
>
>
>On Wed, 25 Jan 2023 12:23:35 -0600, "Mark Chouinard" <chouinard.ok93 at gmail.com> wrote:
>
>Gary,
>
>For whatever it's worth, I also purchase my materials from Paul and Allen at
>Max Gain and I'm about 2 hours up the road from you.
>
>Not trying to pressure, but if down time is a factor I can get you fixed up.
>
>
>Shoot me an email direct at mark at cubexquads.com or call 918-237-0844 if
>you'd like to discuss OD and length.
>
>73,
>Mark - K5YAC
>
>-----Original Message-----
>From: okdxa-bounces at mailman.qth.net  On
>Behalf Of kodiak
>Sent: Wednesday, January 25, 2023 12:10 PM
>To: okdxa at mailman.qth.net
>Subject: [OKDXA] Gary - Parts for Hexbeam
>
>Gary:
>
>I used to operate a KIO Hexbeam at my old QTH in Edmond, and had similar
>experiences with snapped fiberglass spreader arms.
>
>I used the following supplier, they have Hexbeam parts to fit most brands,
>have reasonable prices, and fast shipping:
>
>https://mgs4u.com/product-category/fiberglass-preformed-shapes/fiberglass-ki
>ts/hexbeam-antenna-parts/
>
>73's
>
>Brian, AA5H
>3W9OK
>______________________________________________________________
>OKDXA mailing list
>Home: http://mailman.qth.net/mailman/listinfo/okdxa
>Help: http://mailman.qth.net/mmfaq.htm
>Post: mailto:OKDXA at mailman.qth.net
>
>This list hosted by: http://www.qsl.net
>Please help support this email list: http://www.qsl.net/donate.html
>
>______________________________________________________________
>OKDXA mailing list
>Home: http://mailman.qth.net/mailman/listinfo/okdxa
>Help: http://mailman.qth.net/mmfaq.htm
>Post: mailto:OKDXA at mailman.qth.net
>
>This list hosted by: http://www.qsl.net
>Please help support this email list: http://www.qsl.net/donate.html
>
>
>
>
>______________________________________________________________
>OKDXA mailing list
>Home: http://mailman.qth.net/mailman/listinfo/okdxa
>Help: http://mailman.qth.net/mmfaq.htm
>Post: mailto:OKDXA at mailman.qth.net
>
>This list hosted by: http://www.qsl.net
>Please help support this email list: http://www.qsl.net/donate.html