[OKDXA] WSJT-X and Kenwood TS-590SG

[af5cc at fidmail.com]

Hi Mark,
 
I have used the Kenwood TS590 successfully with WSJT-X using just a USB cable between the radio and laptop.  Makes for a very nice easy setup.
 
Here are a couple of things I can think of, you might have already checked them out:
 
1. Is the CAT rate (Baud rate) set for the same on WSJT and on the radio?  I think on the radio once you set the CAT rate you have to turn the radio off and on again to get it to change to the new rate.
 
2.  I think the Handshake needs to be set for Hardware for the TS590.  Don't know if you have tried that or not.
 
Here is a video that might help:
 
[ https://www.youtube.com/watch?v=PyUs6KkPr6E ]( https://www.youtube.com/watch?v=PyUs6KkPr6E )
 
 
Good luck with it.  The TS590SG is a fantastic radio!  It makes me wonder what the TS890 must be like to be ever higher level.
 
73 John AF5CC
 
-----Original Message-----
From: "Mark Chouinard" <chouinard.ok93 at gmail.com>
Sent: Tuesday, December 13, 2022 9:09pm
To: "'Oklahoma DX Association'" <okdxa at mailman.qth.net>
Subject: [OKDXA] WSJT-X and Kenwood TS-590SG



Fellow OKDX'ers,



I'm tired of missing out on the opportunities FT8 provides and wanted to
give it a try again. I played around with WSJT-X, WSJT-X Alert, and N3FJP
for logging back in 2018/19. The entire setup functioned well and I made
several hundred contacts, but honestly I got bored with the mode and haven't
used it since. 



During the past several months I've been too busy to get on the radio much
except for dabbling in a few contests. The frequent spots on the reflector
have me thinking that I could dart into the shack more often for a quick QSO
or two if I would just get things fired up ahead of time. I've updated to
the latest version, but I'm having com problems between WSJT-X and my
Kenwood TS-590SG. I know this issue is vague, but I'm a bit stumped and
wondering if it might be a problem specific to the TS-590 or Kenwood radios,
so I figured I'd throw it out to the group. 



I'm receiving audio and decoding fine but cannot figure out what happened to
the rig control. I'm certainly connected via the rig's USB com port as I am
able to use this same port for rig control in N1MM, HDSDR, ACLog, Kenwood's
CAT control interface and other digital apps/modes. None of those
applications have a problem and are all configured the same port (Com 5, N,
8, 1, etc.). It doesn't appear to be a conflict with other apps as I've
attempted to run WSJT-X from a fresh restart with no other applications
running. 



I know this is a long shot as com problems are challenging even in person,
but I thought I'd ask the group to see if there might be a known issue with
the latest WSJT-X release and/or the 590 specifically. Perhaps someone
using a 590SG could send me their WSJT-X rig control parameters so I can
compare? Kind of a drag, and I hate being defeated by my radio gear. 



If you are a Kenwood op, or have helpful suggestions, feel free to reply
direct so we don't bore the group. 



73,

Mark - K5YAC



______________________________________________________________
OKDXA mailing list
Home: http://mailman.qth.net/mailman/listinfo/okdxa
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:OKDXA at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html