[NJARC] Help with Philco Transitone 53-562

[sgt88 at atlanticbb.net]

Dear Walt & Aaron:

Excuse me for not mentioning previously...it's not the tube saver...I found 
that one in the wiring...and on the schematic & parts list....got the 
schematic on Nostalgia as per the Philco number..

See no varistor...is that a long slim wirewound?

Sooooooo...the tube wiring is correct...

I'll just replace that big 47K carbon...what wattage is 1-1/8 inches long x 
1/2 diameter...??...hard to imagine that much current to actually split the 
carbon like a knife slicing it lengthwise....!!...Hmmmm...what caused 
THAT????

Might you be able to email YOUR schematic....

Tnx,
S


On Thu, 04 Apr 2013 17:04:08 -0400
  Aaron Hunter <ahunter01 at comcast.net> wrote:
>  Steve
>
>  Don't worry about the 12AV6 connections.  If you trace the schematic out closely, you will see they do connect together.  But then, you didn't say whose schematic you're using.
>
>  The schematics I looked at have a varistor between the 35C5 and 12BA6.  But no matter where it's located as long as it's in the filament string.  To quote the Philco service sheet, "R12 100", "tube saver resistor approx 880 ohms at room temperature."  If I did all my math. correctly, with a resistor rated at 100 ohms with 0.15 amp. going through it, it drops 15 volts.  Adding all the tubes and the resistor, that's an operating voltage of 122.8 volts.  The service sheet says 105 to 120 volts so I guess I'm on target so far.  15 volt drop times 0.15 amps. gives 2.25W dissipation.  You should double the wattage to be safe.
>
>  Aaron
>
>  w2wiq1 at juno.com wrote:
>>  Just remember
>>  Reply = Poster
>>  Reply All = Everyone
>>
>>  _________________________________________________________
>>  HI STEVE:
>>
>>  THE 12AV6 ARE SUPPOSED TO BE CONNECTED TOGETHER AND THEY GO TO THE COMMON GROUND.NOT CHASSIS GND.
>>
>>  LOOKING AT THE FILAMENT STRING 35C5 PIN 3 AND THE 12BA6 PIN 4 IS THAT VARISTORTHERE?
>>
>>  WALTER-W2WIQ
>>
>>  ---------- Original Message ----------
>>  From: <sgt88 at atlanticbb.net>
>>  To: <njarc at mailman.qth.net>
>>  Subject: [NJARC] Help with Philco Transitone 53-562
>>  Date: Thu, 04 Apr 2013 15:21:44 -0400
>>
>>  Just remember
>>  Reply = Poster
>>  Reply All = Everyone
>>
>>  _________________________________________________________
>>  Just put it onto the bench...
>>
>>  split/blown BIG resistor not shown on schematic..nor parts list:
>>  Â Â Â Â 47K ...1-1/8 inches long x 1/2 diameter = old 10 watter??
>>       between pin 4 of 35W4 and pin 2&3 of 12AV6
>>
>>  2.  pins 2 & 3 of that 12AV6 are surely soldered together:
>>        schematic shows NO connection with these two pins????
>>
>>  Do not have "Notes" which may show addition of these details....
>>
>>  Curious that my ( first? ) radio problem doesn't match with the Philco pages...
>>
>>  "Help".......
>>
>>  Tnx,
>>  Steve
>>  ______________________________________________________________
>>  NJARC mailing list
>>  Home: http://mailman.qth.net/mailman/listinfo/njarc
>>  Help: http://mailman.qth.net/mmfaq.htm
>>  Post: mailto:NJARC at mailman.qth.net
>>
>>  This list hosted by: http://www.qsl.net
>>  Please help support this email list: http://www.qsl.net/donate.html
>>  ______________________________________________________________
>>  NJARC mailing list
>>  Home: http://mailman.qth.net/mailman/listinfo/njarc
>>  Help: http://mailman.qth.net/mmfaq.htm
>>  Post: mailto:NJARC at mailman.qth.net
>>
>>  This list hosted by: http://www.qsl.net
>>  Please help support this email list: http://www.qsl.net/donate.html
>>
>>
>>   
>