[Motorola] HT-1000 Cloning, RIB and cables

[Richard J. Fiero II W5TFW]

the same ?

 wait a min !

 I have both and they are not the same.

                                                    Joey



                                                      A.R.S. W5TFW
                                                      Richard J. Fiero II

                                                      www.6mt.com
                                                      www.w5tfw.com

 LIFE'S   TOUGH !

 It's even tougher, if you are STUPID !

                                          John Wayne
----- Original Message ----- 
From: "K0DAN" <k0dan at comcast.net>
To: "Discussion of equipment manufactured by Motorola" 
<motorola at mailman.qth.net>
Sent: Wednesday, May 05, 2010 6:28 PM
Subject: Re: [Motorola] HT-1000 Cloning, RIB and cables


> Here's HT600/MT1000 cloning instructions. The HT1000 is identical or very
> similar. You can build up your own cloning cables but the trick will be
> finding suitable accessory connectors for the radios. One trick is to cut 
> up
> a pair of speaker-mics and splice the cables/pins as needed. The BATLABS
> site should have documentation on the pinouts.
>
> Good luck.
>
> dt
>
> INSTRUCTIONS FOR USE OF THE HT600/MT1000 CLONING CABLE
>
>
>
>
>
> 1. Remove the covers on the top of the radios which protect the external
> audio/data I/O connectors (Universal Connector).
>
>
> 2. Connect the cloning cable to the Universal Connector of both radio A 
> (the
> "master") and radio B (the "slave").
>
>
> 3. Turn OFF radio A.
>
>
> 4. Turn ON radio B.
>
>
> 5. Place the PL switch on radio A to the carrier squelch position (shows a
> speaker symbol with no line through it) for full cloning. Full cloning 
> will
> duplicate all frequency, PL, paging, deviation, squelch, and volume 
> settings
> from radio A to radio B.
>
>
> 6. Simultaneously depress the PTT and monitor button on radio A and hold.
>
>
> 7. Turn on radio A. The green LED on radio B will flash
>
> indicating cloning is in progress.
>
>
> 8. Cloning is complete once the green LED turns off and an alert tone is
> heard from radio B.
>
>
> 9. Release both PTT and monitor button on radio A.
>
>
> 10. Replace protective cover on Universal Connectors.
>
>
>
> ----- Original Message ----- 
> From: "Coote, Jay" <jcoote at ci.arcadia.ca.us>
> To: "Discussion of equipment manufactured by Motorola"
> <motorola at mailman.qth.net>
> Sent: Wednesday, May 05, 2010 5:28 PM
> Subject: [Motorola] HT-1000 Cloning, RIB and cables
>
>
>> List-
>>
>> A few HT-1000 questions, on behalf of a military unit:
>>
>> 1.    Can the HT-1000s be cloned, if so, what is the procedure and
>> cloning cable?
>> 2.    Are there schematics for building your own cloning and programming
>> cables?
>> 3.    Are there cheap, alternative sources for buying new  HT-1000
>> programming and cloning cables?
>>
>> Thanks,
>>
>> Jay
>>
>>
>> ______________________________________________________________
>> Motorola mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/motorola
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Motorola at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>>
>
> ______________________________________________________________
> Motorola mailing list
> Home: http://mailman.qth.net/mailman/listinfo/motorola
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Motorola at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html