[Milsurplus] PE-104-A Power Unit Vibrator Help

[Carl Reinemann]

I saw the article and have a link to it
http://www.radionerds.com/index.php/File:Wire_VBN-1.pdf

Here is the group out of Britain building replacements for various pieces
(not the SCR 284) https://www.royalsignals.org.uk/vibs/

Is there someone willing to take a look to see how it could be done? I just
don't have the technical background to figure it out. Give me instructions,
and I can solder it up though.

Carl

On Thu, Feb 22, 2018 at 1:01 PM, Tom <noflood1 at sonic.net> wrote:

>   I'm also interested in how to wire the BC-654 Vibrator using this VBx-1
> module. I helped N7CAV do a story on using this same module to modify the
> vibrator used in the  DY-88 power supply for the GRC-9. The article with
> instructions was in Electric Radio Magazine last year. Aside from the
> module two 1N5406 diodes are added, I'm unsure how to do the same
> conversion on the BC-654 vibrator, a wiring diagram would be useful.
>
>
>  I bought my VBx-1 modules from
>
> Bob's Radio & TV
>
> 1415 S. 4th St. <https://maps.google.com/?q=1415+S.+4th+St.%0D+Oceano,+CA+93445&entry=gmail&source=g>
>
> Oceano, CA 93445 <https://maps.google.com/?q=1415+S.+4th+St.%0D+Oceano,+CA+93445&entry=gmail&source=g>
>
> 805-489-8200 <(805)%20489-8200>
>
>      They have a website.
>
>                                                       Tom, W6TOM
>
>
>
>
> On 2018-02-22 09:43, Rob Lee wrote:
>
> Carl,
>
> The TBX power supply also has a 6 pin synchronous vibrator along with a 4
> pin. I haven't reached the point of wiring it up. The synchronous vibrator
> is addressed in the VBx-1 Connections paragraph in the document previously
> sent. Attached is an additional document referencing the two diodes used in
> conjunction to replace a synchronous vibrator. See the lower right corner
> of the diagram.
>
> I believe the Aurora Design VBx-1 Electronic Vibrator is only available
> via dealers. I purchased a couple from a local radio repair shop that
> specializes in vintage car radios.
>
> Bill Newman
> 301 E Wallace Kneeland Blvd
> <https://maps.google.com/?q=301+E+Wallace+Kneeland+Blvd%0D+Suite+224&entry=gmail&source=g>
> Suite 224
> <https://maps.google.com/?q=301+E+Wallace+Kneeland+Blvd%0D+Suite+224&entry=gmail&source=g>
> -229
> Shelton WA 98584
> 360 427-0513 <(360)%20427-0513>
> bill at billtheradioguy.com
>
> Let me know if you are able to dig up any additional reference material.
>
> Rob
>
> ----- Original Message -----
> *From:* Carl Reinemann <creinemann at gmail.com>
> *To:* milsurplus at mailman.qth.net
> *Sent:* Thursday, February 22, 2018 7:44 AM
> *Subject:* Re: [Milsurplus] PE-104-A Power Unit Vibrator Help
>
> Thanks, Rob,
> Where did you order your modules from?  Here is the schematic for the
> PE-104-A.  I am clear on the mechanics of taking the vibrator apart, and
> reconfiguring the existing unit, but I am not clear on the actual wiring up
> of the new modules to this kind of vibrator as it has 6 pins, whereas the
> examples I have seen are seven or four pin units.
>
> Carl
>
> On Wed, Feb 21, 2018 at 10:48 PM, Rob Lee <rob at k7tgu.com> wrote:
>
>> Carl,
>>
>> Attached is the spec sheet I have. Not sure if it will be any help.
>> Ordered a couple of these for use in a TBX 12V power supply, but haven't
>> gotten back to the project. Will dig a little deeper to see if I have
>> additional documentation.
>>
>> Rob
>>
>> ----- Original Message -----
>> *From:* Carl Reinemann <creinemann at gmail.com>
>> *To:* milsurplus at mailman.qth.net
>> *Sent:* Wednesday, February 21, 2018 5:15 PM
>> *Subject:* [Milsurplus] PE-104-A Power Unit Vibrator Help
>>
>> Has anyone converted a Radiart VS-3 Vibrator used in the PE-104-A Power
>> Unit of  BC-654 Radio set to solid state using the VBN module?
>>
>> I have been following this thread on the G503.com site
>> http://forums.g503.com/viewtopic.php?f=36&t=205860&p=1708669#p1708669
>>
>> My SCR-284 is working (for now) but I would like to convert that vibrator
>> to solid state if any one could help with a wiring diagram.
>>
>> Carl
>>
>>
>> ------------------------------
>>
>>
>> ______________________________________________________________
>> Milsurplus mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/milsurplus
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Milsurplus at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>>
>>
>>
> ------------------------------
>
>
> ______________________________________________________________
> Milsurplus mailing list
> Home: http://mailman.qth.net/mailman/listinfo/milsurplus
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Milsurplus at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
>
> ______________________________________________________________
> Milsurplus mailing list
> Home: http://mailman.qth.net/mailman/listinfo/milsurplus
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Milsurplus at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mailman.qth.net/pipermail/milsurplus/attachments/20180223/59a57215/attachment-0001.html>