[Lowfer] WD2XNS WSPR-15 / WOLF pre-test test

[Stan, W1LE]

Thanks Jay, I am progressing.....

I set the RX to USB ( from CW rev) and I started to get spectra on the 
WSPR-X V0.7 r2960 waterfall display at 1614 Hz.

I am now getting the WOLF decode at 1W (your TX) and I am waiting for a 
WSPR-X decode.

Now have a WSPR-X decode at -35 dB.

Only in a semicalibrated mode right now. I calibrated at CW rev at 
136.800Khz. WOLF offset is about -0.16 Hz

Stan, W1LE   Cape Cod




On 2/17/2013 12:23 PM, jrusgrove at comcast.net wrote:
> Stan
>
> Yes ... it is WSPR-X that you want.
>
> I would suggest the receiver be set to 136000 USB. The WOLF signal 
> will then be centered on 800 Hz. Set the WOLF decoder frequency to 800 
> Hz. The WSPR-X waterfall should show the WSPR-15 signal at 136000 +1614.
>
> Jay
>
>
> ----- Original Message ----- From: "Stan, W1LE" <stanw1le at verizon.net>
> To: <dexter.mc at gmail.com>; "Discussion of the Lowfer (US, European, 
> &amp; UK) and MedFer bands" <lowfer at mailman.qth.net>
> Sent: Sunday, February 17, 2013 11:12 AM
> Subject: Re: [Lowfer] WD2XNS WSPR-15 / WOLF pre-test test
>
>
>> Wolfie into Cape Cod at 10W.
>>
>> Any pointers to WSPR-15 ?  I found a -20 and a -30 but no -15.
>> Is it the latest X mode ?
>>
>> Do I keep the RX parked at 136.800 KHz for the WSPR  and the WOLF ?
>>
>> Stan, W1LE   Cape  Cod FN41sr
>>
>>
>> On 2/17/2013 10:59 AM, Dexter McIntyre W4DEX wrote:
>>> Up and running:
>>>
>>> 2013-02-17 15:50:57 >WOLF10  -r 12000.75 -f 800 -t 1.0 -w 0.0000
>>> t:  24 f:-0.768 a: 0.8 dp: 94.1 ci: 6 cj:441 YVPEZ2AKZ /A7 J ?
>>> t:  48 f:-0.043 a:-0.6 dp: 92.0 ci:14 cj:458 WD2XNS 10W TX   -
>>> t:  96 f: 0.001 a:-1.5 dp: 91.9 ci: 5 cj:375 ZPYDUZNLT1WLK25 ?
>>> t: 192 f:-0.039 pm:495.8 jm: 45 q:  5.4  5.0 WD2XNS 10W TX   -
>>> t: 288 f:-0.039 pm:929.9 jm: 45 q:  7.7  7.8 WD2XNS 10W TX   -
>>> t: 384 f:-0.039 pm: 1326 jm: 45 q:  9.1  9.3 WD2XNS 10W TX   -
>>> t: 480 f:-0.039 pm: 1723 jm: 45 q: 10.0 10.7 WD2XNS 10W TX   -
>>>
>>> The only place I had my sound card sampling rate saved was in the 
>>> wolf setup.  I still have the previous version wolf but the saved 
>>> sampleing rate went to default after launching the latest wolf. So I 
>>> just guessed at the 12000.75 and it was close.  I'll just use your 
>>> transmission to tweak the rate for now.
>>>
>>> Dex
>>
>> ______________________________________________________________
>> Lowfer mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/lowfer
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Lowfer at mailman.qth.net
>> Post must be less than 50KB total for message plus attachment!
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html 
>
> ______________________________________________________________
> Lowfer mailing list
> Home: http://mailman.qth.net/mailman/listinfo/lowfer
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Lowfer at mailman.qth.net
> Post must be less than 50KB total for message plus attachment!
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>