Re[2]: [Logic] QSX Radio frequency

Sat, 23 Mar 2002 10:42:09 -0700

I ran into this same problem using an ICOM 756 PRO.  If you are using
TRX-Manager then split works fine.  I talked to the folks at Logic and
they  are aware of this.  Their Icom driver does not appear to work as
good as the on in TRX-Manager.

-- 
73,

Tom                            mailto:[email protected]

Saturday, March 23, 2002, 10:02:15 AM, you wrote:

BHN> On some radios, Icoms come to mind, the TX VFO frequency cannot be read by
BHN> the computer unless it is made the active VFO.

BHN> Ben
BHN> ----- Original Message -----
BHN> From: "Jim Brannigan" <[email protected]>
BHN> To: <[email protected]>
BHN> Sent: Saturday, March 23, 2002 08:54
BHN> Subject: Re: [Logic] QSX Radio frequency

>> A note to OMNI-VI+ users.
>> I find that if I set the split from the radio, Logic6 will not log the
BHN> Xmt.
>> Freq.
>> If I set the split from the log window, the Xmt. freq. is logged and the
>> packet QSX is sent.
>> This is a problem with the Ten Tec software.
>> Jim
>>
>> > Hi
>> > The split Frequency  works Fine for me and automatically on my
>> > Kenwood 950 SDX that is connected to the computer via com 1 via Kenwood
>> > interface IF-232C
>> > In other words if your radio is connected to the computer and logic can
>> > control it  the split frequency works automatically
>> >
>> > 73 Eli  4z5is
>> >
>> > Stern Eli  Advocate & Notary
>> > ham radio callsign    4Z5 IS
>> > ____________________________________
>> > [email protected]                  OFFICE
>> >
>> > Haberman Dovev & Stern advocates & notarie  Office
>> > 51 Wizman St Tel Aviv Israel
>> > FAX  00972 3 6962206
>> >
>> > [email protected]           HOME
>> >
>> > 2 sagie st P.O.BOX 728   Reut ISRAEL 71908
>> > Fax  00 972 8 9710010
>> >
>> >
>> >
>> > -----Original Message-----
>> > From: [email protected] [mailto:[email protected]]
>> > On Behalf Of GilBaronW0MN
>> > Sent: Saturday, March 23, 2002 3:14 PM
>> > To: AA/Logic
>> > Subject: [Logic] QSX Radio frequency
>> >
>> > In the log form there is a field for transmit frequency when operating
>> > split. Is there a way to automatically update this field to the exact
>> > transmitted frequency as read from the rig rather than nothing or
>> > offset?
>> > I would like the program to read the other vfo and enter the frequency
>> > here.
>> > It would make sending spots so much more useful. On clusters if you have
>> > QSX
>> > (XMIT FREQ) then the spot logs will show this and logic users and others
>> > that have the feature can set the split automatically. Since the set rig
>> > automatically sets the split if on the spot log, that  means it has
>> > access
>> > to the other vfo. I assume there should be a way to read it also. Is
>> > there a
>> > way to do that or do you have to manually enter this field?
>> >
>> >
>> > Gil Baron http://webpages.charter.net/gbaron
>> > 44.08208 N 92.51263 W 1055'
>> > "Hierro candente, batir de repente"
>> >
>> >
>> > _______________________________________________
>> > LOGic mailing list
>> > [email protected]
>> > http://mailman.qth.net/mailman/listinfo/logic
>> >
>> > _______________________________________________
>> > LOGic mailing list
>> > [email protected]
>> > http://mailman.qth.net/mailman/listinfo/logic
>>
>> _______________________________________________
>> LOGic mailing list
>> [email protected]
>> http://mailman.qth.net/mailman/listinfo/logic
>>

BHN> _______________________________________________
BHN> LOGic mailing list
BHN> [email protected]
BHN> http://mailman.qth.net/mailman/listinfo/logic