[Johnson] T/R relay

[Carl]

The only 'normal' reason for desensing with an electronic T/R Switch would
be operation on a band the TX is not tuned to. If that isn't what you're
doing, I would make certain your Fast/Slow AGC setting on the receiver isn't
the cause, then I would swap the 6BL7. After that, you start getting into
some component problem within the 250-39. One thing you can do about the
heat: paint the cabinet black. Most of whatever that finish is on my 250-39s
is crummy, one way or another (usually the front panel on mine.) So painting
the cabinet isn't going to hurt the value. This provides a nice opportunity
to 1st drill out the rivets and swap the connectors. If you care about
matching such things, DX-Engineering sells the Amphenol SO-239s with that
glass-reinforced PBT insulation material (as opposed to 'modern' TFE.) See:
http://www.dxengineering.com/parts/dxe-83-1r-kit


** More of the usual overpricing from DXE, I make it a point to buy nothing 
from them.
That connector is $3.28 at Mouser who has no minimum, and low shipping when 
USPS First Class is requested.


About replacing the rectifier in any boatanchor: you can do it, but the B+
is going to go way up, so you need to make some measurements 1st. Measure
the HV, then the current. Replace whatever rectifier, then again measure the
B+. That will give you a value for an appropriate dropping resistor-both
ohms and power. Add the resistor, measure until you have the resistor value
right, and you are back to operation with the original voltage level.

** And at no heat savings other than the tube filament and at the same time 
the transformer is running harder due to the hard switching of the SS.
You wind up with a net gain of zero in most of those swaps.


Obviously, this is much more reasonable when there isn't a lot of current,
and when that current is steady-such as in a T/R Switch.

Other points about T/R Switches:
1) Fusing. I always add a subminiature 250VAC-rated TO-5
transistor-sized fuse (typically a 1 or 2A SB) internally. Fuses are
primarily disaster prevention devices, and for something like a T/R Switch 1
or 2A SB is fine. The EFJ 250-39 uses the EFJ fused-plug with a 2-wire cord.
By adding a small internal fuse, you can use a 3-wire cord which I am much
more comfortable with, and without violating my Rule 1-for-Boatanchors: I
don't make no new holes.
2) Rectifiers. I (pardon the heresy here on EFJ) really like the
broadband B&W 380B and the B&W 381-which adds bandswitching, and hence some
selectivity. The latter T/R SW is somewhat hard to find.

** I use a pair of Johnsons and a pair of B&W 381-C's, the B&W has a better 
SNR on 10 and 15M but only with a fairly noisy radio to start with. None of 
the T/R switches will help already hot performers and just raise the noise 
plus signal.


The B&Ws use a
selenium rectifier and a 2 wire cord with no fusing (there MAY be an
internal fusible link (one individual wire from the stranded 2 wire cord
wire.) Replacing any selenium rectifier is always a good idea since the
fumes from a burned-out selenium rectifier are a definitely poisonous gas.

** First Ive ever heard the selenium fumes are toxic or a poisonous gas. 
They will certainly clear a room/house with the stink but AFIK they havent 
killed anyone and millions were used in consumer electronics (-; including 
Johnsons.

Carl
KM1H



Same measurement techniques.

I have some of these same comments on my website which REALLY needs
attention now that I have retired:

http://www.n4xy.com/accessories-2.html

Ed Tanton  N4XY  n4xy at comcast.net
189 Pioneer Trail
Marietta, GA  30068-3466
U.S.A.

EFJ Reflector Manager

website: http://www.n4xy.com

Member: ARRL(LM)  AMSAT(LM)
QCWA(LM) SEDXC NCDXF INDEXA(LM)
OKQRP Elecraft K2 Beta Tester

All emails <IN> & <OUT> checked by
Norton AntiVirus with AutoProtect

-----Original Message-----
From: johnson-bounces at mailman.qth.net
[mailto:johnson-bounces at mailman.qth.net] On Behalf Of Charles Ring

I have used the 250-39 Johnson T/R switch since 1967. I've had 3 of them and
the power transformer on two of those have failed. Since returning to the
air a year ago I've been using one with my Globe King 500A and Drake R-4C.
It works, but unlike long ago, I can't get full QSK. The receiver is being
badly desensed. I don't remember if it did better then with the R-4C or if
that was only with the 2-C and the R-4B, both of which are waiting for
repairs. I am interested in changing to either a fast relay or a PIN diode
switch. I seldom do faster than 25WPM.

73 de W3NU




______________________________________________________________
Johnson mailing list
Home: http://mailman.qth.net/mailman/listinfo/johnson
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Johnson at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html


-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1432 / Virus Database: 3204/5982 - Release Date: 07/11/13