[ICOM] Icom Filters, controller, bracket, mic, cables and more FS

Ken, W8EK kenw8ek at gmail.com
Thu Jul 5 08:59:22 EDT 2018


Icom Crystal Filters, Screwdriver HF Mobile antenna
controller, mobile bracket, hand mic, cables, and
other Icom items For Sale:
.

.
Icom Crystal Filters:

These are all original Icom crystal filters used in
the 9 MHz IF of many Icom rigs including IC-706,
IC-725, IC-726, IC-728, IC-729, IC-736, IC-737,
IC-738, IC-746, IC-756, IC-757, IC-780, IC-781 and
probably others. They should fit any Icom rig that
uses a 9 MHz filter, but please check your manual.

Filter number, bandwidth, and price

FL-32 A, 500 Hz CW or narrow digital, $100
FL-80, 2400 Hz standard SSB, $75
FL-101, 250 Hz narrow CW, $95
FL-103, 2800 HZ Wide SSB, $100
.

.
Screwdriver HF mobile antenna controller:

N2VZ TuneMatic Automatic Motorized Antenna Controller

This self-contained antenna controller will automatically
adjust the screwdriver antenna. It operates 1-60 MHz, and
keeps track of the parameters of the antenna. This one is
designed to be used with the Icom IC-7000, but can be
used with other rigs.

This one appears to be new, unused. With paper work for $210.
.

.
BetterRF "Tune Control" for Yaesu:

The BetterRF Company FT-857/897 Yaesu tune controls
are designed to work with Yaesu FT-100, FT-857, and
FT-897 transceivers. They will make the tune button
function to provide a low power output for tuning,
adjusting an antenna, checking SWR, and more, no matter
what mode you are using. The tune controls include an
interface cable. No radio modification is required.

The BetterRF Company FT-857/897 Yaesu tune controls
provide an interface between your YAESU transceiver
and ICOM-type accessories, such as ICOM antenna tuners,
tuners from other manufacturers, and screwdriver antenna
controllers.

This one looks like new. With paper work for $25.
.

.
Icom MB-51 Mounting Bracket

This is an odd mounting bracket that is not often found
in ham circles. It can attach to a dash and swivel to
most any direction. It has a screw to take "head mounts"
such as the MB-63 for the IC-706. Basically it is an
additional way to mount a remote head. It is chrome
plated, and really looks great. $40
.

.
Icom HM-36 Hand Microphone

This is the standard hand microphone that comes with
many modern Icom rigs when new. It has a round 8 pin
connector, and also has up and down switches on top.
This one works fine and looks like new. $30
.

.
DC Power Cable

This is the heavy duty power cable as used on most of
the Icom HF rigs, plus also many Kenwood, Alinco, and others.
It has the 6 pin molex connector, with four pins used - two
for plus and two for ground.
It looks good, and of course works fine. $22
.

.
Modular to 8 pin cable

This cable has a modular flat 8 pin plug on one end and
the standard round 8 pin connector on the other end.

It is a "one to one" cable, in that pin 1 on the modular
connector goes to pin 1 on the round 8 pin connector, pin
2 to pin 2, etc.

This type cable is often used for digital interfaces (such
as West Mountain RigBlastrers, or Tigertronics SignaLinks),
however can be used for other purposes.

This one works and looks fine.  Only $12.
.

.
Cable for Icom Transceiver to Digital Controller:

The package says "The Country Ham RTC2-Ic", TNC-Radio
Cable w/ DIN and Mike Plug. For use with MFJ, AEA, and
PacComm TNCs using a 5 pin DIN plug. The opposite
end has a round Icom 8 pin connector as used on most
Icom rigs. Pin outs are listed on the label.

There is also an attached cable with 1/8 inch plug to
go to the speaker jack.

This cable is apparently new, still in its original bag.

Only $12
.

.
I also have many other accessories of many different
brands available.
Just too many to list here. Please e-mail your requests.

.
Prices do not include shipping from Florida.

Thanks.

73,

Ken, W8EK

Ken Simpson
E-mail to W8EK at FLHam.net or W8EK at arrl.net
Voice Phone (352) 732-8400



.






More information about the Icom mailing list