[ICOM] Icom IC-M700PRO power cable.

[Gary Fiber]

I downloaded the manual for find the part number. Sometimes the amateur HF power cables will work BUT you need to verify the wiring. You can pull back the boot on the M700Pro power pigtail and match the color code. I think the M700Pro uses the same type of 6 pin connector Icom's  Amateur HF transceivers use but it might not be pin for pin match. You could also ask Icom's parts if they will verify with the service department the cable they are sending is the correct power cord. Tell them you have purchased 2 other power cords that did not work from I suspect others and you want to be sure you are getting the correct one. Also you might give a call to Icom's Tech support department, I am not sure if they are still supporting that transceiver but if they are one of the tech support persons could verify what I told you.

I did not ask but  assumed you are needing the cord from the battery that plugs into the back of the M700Pro pigtail.

Gary K8IZ

-----Original Message-----
From: Icom [mailto:icom-bounces at mailman.qth.net] On Behalf Of John K0CQW
Sent: Thursday, July 23, 2015 1:10 PM
To: ICOM Reflector
Subject: Re: [ICOM] Icom IC-M700PRO power cable.

Thanks I will order this one again, This is the 3rd cable that I have received that is wrong. I checked other M700PRO's and the radio connectors are the same on all of the M700PRO's here. So it is not the radio..... No support from a major "marine" Icom dealer.............
 Thanks again, de John KØCQW

On Thu, Jul 23, 2015 at 1:23 PM, Gary Fiber <gfiber at comcast.net> wrote:

> Yes it is in the manual page no. 15 under unpacking the DC Cable is 
> part number OPC-568. I seem to remember it is made of 10 gauge wire 
> and possible wire opposite of Icom's amateur HF rigs. I worked at Icom 
> when this transceiver was sold and I supported it, however to many 
> years have gone by since I last saw one. You can also email Icom America's parts dept.
> directly from Icom America's web page under Support.
>
> Hope this helps
>
> Gary P. Fiber K8IZ
>
>
>
> > On Jul 23, 2015, at 10:40 AM, John K0CQW <k0cqwgroups at gmail.com> wrote:
> >
> > Looking for the Icom part number for the  power cable for the IC-M700PRO.
> >
> > Not in the manual.
> >
> > Called icom at 425 450 6087 three different days at different times,
> waited
> > 15 min each time and did not get though.
> >
> > Looking for the part number for the power cable fpr the IC-M700PRO , 
> > The
> > 700 will not work nor the IC-M892.
> >
> > Thanks de John KØCQW
> > ----
> > Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net Icom 
> > Users Net: Sundays, 1700Z, 14.316 MHz Icom FAQ: 
> > http://www.qsl.net/icom/ To support QSL/QTH.net: 
> > http://www.qsl.net/donate.html
> ----
> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net Icom 
> Users Net: Sundays, 1700Z, 14.316 MHz Icom FAQ: 
> http://www.qsl.net/icom/ To support QSL/QTH.net: 
> http://www.qsl.net/donate.html
----
Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net Icom Users Net: Sundays, 1700Z, 14.316 MHz Icom FAQ: http://www.qsl.net/icom/ To support QSL/QTH.net: http://www.qsl.net/donate.html