[ICOM] IC-7656 Pro 3 Question

[JV]

    That is what you need to put into the computer. Open volume control and
make changes in properties as necessary. All of this is in the manual.  
 
 
 
 
-------Original Message-------
 
From: Conrad & Kathi Nasatka
Date: 2/18/2011 2:56:32 PM
To: ICOM Reflector
Subject: Re: [ICOM] IC-7656 Pro 3 Question
 
How do you do that? Not sure I know what you mean.  The sound card is called
the "USB Audio Codec". The Tigertronics one, that is!
Conrad
----- Original Message -----
From: "JV" <jv at kt4u.org>
To: "Z Icom" <icom at mailman.qth.net>
Sent: Friday, February 18, 2011 2:40 PM
Subject: Re: [ICOM] IC-7656 Pro 3 Question
 
 
>    Is the sound card set on USB?
>
>
>
>
> -------Original Message-------
>
> From: Conrad & Kathi Nasatka
> Date: 2/18/2011 2:32:28 PM
> To: ICOM Reflector
> Subject: Re: [ICOM] IC-7656 Pro 3 Question
>
> Larry:
> It says in the SignaLink USB instructions to turn Vox off.
> I am still getting used to the rig as I only received it on about
> 1/25/2011.
> The SignaLink is connected to the rig via an 8 pin din into acc #1.
> The computer has a line going into the USB port on the computer.
> The speakers are salso wired into the SignaLink USB.
> When i key the program to send a red light comes on the SignaLink USB but
> it
> doesn't key the transmitter.
> I tried pushing the transmit button but nothing happens. There is a tune
> button on the program and I tested it and the
> red light comes on but no transmitter keying.  I pushed the LSB twice to
> get
> the LSB D mode or digital mode.
> I am out of ideas, got any more? It is r  unning in digital mode all the
> time.
> Regards
> Conrad
> WB3DQD
>
> ----- Original Message -----
> From: "Larry Young" <k4lxv at bellsouth.net>
> To: "ICOM Reflector" <icom at mailman.qth.net>
> Sent: Thursday, February 17, 2011 10:50 PM
> Subject: Re: [ICOM] IC-7656 Pro 3 Question
>
>
>> Conrad: While not at all familiar with EasyPal, most software via sound
>> card to the radioprograms require some type of hardware interface to
>> actually key the transmitter. If attempting to run the digital input via
>> the rear panel or the front audio input in digital mode you most definate
>> hardware means to implement the ptt of the proIII. Rhe radio vox operates
>> only via the front panel mic input, but not in digital mode.
>> Larry K4LXV
>>
>> --- On Thu, 2/17/11, Conrad & Kathi Nasatka <konco at ptd.net> wrote:
>>
>> From: Conrad & Kathi Nasatka <konco at ptd.net>
>> Subject: [ICOM] IC-7656 Pro 3 Question
>> To: "ICOM Reflector" <icom at mailman.qth.net>
>> Date: Thursday, February 17, 2011, 6:16 PM
>>
>> I recently purchased an ICOM 756 Pro 3 and am having problems getting
>> Easy Pal to key the transmitter.
>> I am hoping I can get an answer from someone on the list
>> Regards
>> Conrad
>> WB3DQD
>> ----
>>
>> ----
>> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
>> Icom Users Net: Sundays, 1700Z, 14.316 MHz
>> Icom FAQ: http://www.qsl.net/icom/
>> To support QSL/QTH.net: http://www.qsl.net/donate.html
>>
>
> ----
> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
> To support QSL/QTH.net: http://www.qsl.net/donate.html
> ----
> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
> To support QSL/QTH.net: http://www.qsl.net/donate.html
>
 
----
Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
Icom Users Net: Sundays, 1700Z, 14.316 MHz
Icom FAQ: http://www.qsl.net/icom/
To support QSL/QTH.net: http://www.qsl.net/donate.html