[ICOM] For Sale: Classic ICOM gear

[Gary P. Fiber]

I think the OPC-118 will actually feed back an ALC voltage to the 751A 
so the power control would be automatic as the AH2A controller has an 
ALC adjustment inside of it. BUT I am trying to remember the OPC-118 and 
the connections that were available inside and it may not have the ALC 
connection. Its been a long time now since I actually worked for Icom. 
Sounds like some nice vintage equipment you have there. Good station for 
anyone.

73,

Gary K8IZ

On 9/30/2010 3:39 PM, Edward Dickinson, III wrote:
> Gary - right on the UX-14.  One must manually turn down the power on
> pre-IC-735 rigs(?).  One advantage to that...One can tune at low power and
> bring the power up some and find a more precise tune (lower SWR) under
> higher power.  I'll not attempt to quantify 'higher power', but I never had
> any issues here (IC-735, 730, 740, 745, 751A).
>
> -----Original Message-----
> From: icom-bounces at mailman.qth.net [mailto:icom-bounces at mailman.qth.net] On
> Behalf Of Gary P. Fiber
> Sent: Thursday, September 30, 2010 6:24 PM
> To: ICOM Reflector
> Subject: Re: [ICOM] For Sale: Classic ICOM gear
>
> You are correct on the RC-10. The AH2A with the controller will work with
> the IC-751A but you need the UX-14 installed to make it work like it does
> with the IC-735.
>
> Gary K8IZ
>
> On 9/30/2010 3:09 PM, Edward Dickinson, III wrote:
>    
>> For Sale:
>>
>> IC-751A late model - PBT
>> 	Optional Internal Power Supply
>> 	Non-Volatile RAM Backup
>> 	60 Meter enabled
>> 	HM-12 Hand Mic
>> 	Ceramic Trimmer Capacitors
>> 	Manual, Schematics, Copy of Service Manual
>> 	Cosmetic 7 - Has good repaint (was mobile at times)
>> 	    - couple of touched-up scratches on top edge of Front Panel
>> 	$500 + shipping
>>
>> AH-2a   Tuner - By itself, same electronically as AH-3
>> 	Works with IC-725, 726, 728, 729, 706 and all current ICOMs with 4
>> Pin Tuner Connection
>> 	Some marks on plastic tuner body
>> 	SO-239 Input installed
>> 	Will work with non-ICOM gear with simple tune actuation circuit
>> (resistor, diode, LED)
>> 	Manual, schematics
>> 	$220 + shipping
>> AH-2a  Control Head
>> 	Adapts IC-730, 735, 740, 745, 751/A to Tuner
>> 	$60 + shipping (needs OPC-118 for those above other than 735)
>> OPC-118  7 and 8 pin to 24 Pin Molex adaptor
>> 	$25 mailed CONUS
>> (AH-2a  Tuner, Control Head and OPC-118
>> 	$250 + shipping)
>>
>> IC-RC10  Frequency Control Pad for IC-751/A (only, AFAIK)
>> 	$50 mailed CONUS
>>
>> SM-8 	Desk Mic
>> 	Two Cords - switchable between two rigs from mic
>> 	(2nd cord/plug not ICOM original)
>> 	Instruction sheet
>> 	$120 + shipping
>>
>>
>> Offered here first - to the trade boards next week Offers..?
>>
>> Please contact off list.
>>
>>
>> 73,
>> Dick - KA5KKT
>> (Lexington, KY)
>>
>>
>>
>>
>>
>> ----
>> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net Icom
>> Users Net: Sundays, 1700Z, 14.316 MHz Icom FAQ:
>> http://www.qsl.net/icom/ To support QSL/QTH.net:
>> http://www.qsl.net/donate.html
>>
>>
>>      
>
> --
> Gary P. Fiber K8IZ
> Electronic Communications Systems Technician - Field General Radio Telephone
> Operators License PG-19-6691,
>    with Shipboard Radar Endorsement.
> Washington State Resident.
>
> ----
> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net Icom Users
> Net: Sundays, 1700Z, 14.316 MHz Icom FAQ: http://www.qsl.net/icom/ To
> support QSL/QTH.net: http://www.qsl.net/donate.html
>
> ----
> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
> To support QSL/QTH.net: http://www.qsl.net/donate.html
>
>    


-- 
Gary P. Fiber K8IZ
Electronic Communications Systems Technician - Field
General Radio Telephone Operators License PG-19-6691,
  with Shipboard Radar Endorsement.
Washington State Resident.