[ICOM] IC-718 antenna tuning and SWR

[kb8rtz at oh.rr.com]

Correct, the IC-718 is AM/SSB/CW/RTTY only.

The CW mode was set to full break-in as per the manual. So am I correct that in CW mode with the PTT engaged the transmitter produces no carrier unless the electronic DIT or DAH key is pushed (which, by the way, doesn't require the PTT button)? And while in RTTY mode the PTT does produce a carrier?  With respect to CW and PTT the manual is a little confusing or misleading.

Ahh, I should put my HTX-10 on the air to listen for the signal generated in both CW and RTTY modes from the IC-718 on 10m.

Going to continue working with the Tx and antenna after work today.

Thanks for all of your encouragement. Will report when all is finally good.

Patrick...KB8RTZ...

---- "Gary P. Fiber" <gfiber at comcast.net> wrote: 

=============
The IC-718 does not have FM and the Tune button does nothing unless an 
Icom or similar tuner is attached.
He needs to use CW mode with a CW key and BK-IN enabled, AM mode and 
press the PTT on the mic, RTTY mode and press the PTT to send a carried 
to check SWR.

Gary K8IZ


On 6/25/2010 12:55 AM, Hal WD4MDA wrote:
> Patrick,
> I meant to include.
> If you set the rig in rtty or fm and hit the tune button you should get a
> swr reading.  I use foot switches here but it is all the same except for Cw
> mode.
>
> 73,
> Harold "Hal"  Stang / WD4MDA
> wd4mda at comcast.net
> wd4mda at yahoo.com
> Yahoo IM @ wd4mda
> Field Hell - #2599
> 30mdg - #3772
>
> ----- Original Message -----
> From:<kb8rtz at oh.rr.com>
> To: "ICOM Reflector"<icom at mailman.qth.net>
> Sent: Thursday, June 24, 2010 9:53 PM
> Subject: [ICOM] IC-718 antenna tuning and SWR
>
>
>    
>> Good evening,
>>
>> I have an IC-718 and am attempting to narrow an SWR issue with a new
>> Hustler 6BTV. The last few days have been frustrating to say the least.
>> The instructions in the Tx manual say to set the power above 30W, set the
>> operating mode to either CW or RTTY, set the display to show SWR; tune to
>> a frequency and push the PTT button. Realized that I didn't follow the PTT
>> instruction and have instead been pushing the DIT command on the
>> electronic microphone keyer to check SWR.
>>
>> Anyway, on 10m the SWR seemed just fine using the CW DIT command. On all
>> bands (10-15-20-40 check so far) while in CW mode and pushing PTT the SWR
>> reads 1:1 or less. While in RTTY mode the SWR on 10m slopes upward from
>> 1.75:1 at the low end to 2.5:1 at the high end. The SWR in CW mode and
>> pushing the DIT command the SWR was even higher.
>>
>> My questions are:
>> Why when pushing PTT in CW mode there is no SWR reading?
>> Why when pushing PTT in RTTY mode there is SWR?
>> Why when pushing DIT command on the electronic microphone keyer there is
>> SWR?
>> The last question comes from the manual stating to set to either CW or
>> RTTY then push PTT to read the SWR.
>>
>> Thanks much.
>>
>> 73...Patrick...KB8RTZ...
>> ----
>> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
>> Icom Users Net: Sundays, 1700Z, 14.316 MHz
>> Icom FAQ: http://www.qsl.net/icom/
>> To support QSL/QTH.net: http://www.qsl.net/donate.html
>>      
>
> --------------------------------------------------------------------------------
>
>
>
> No virus found in this incoming message.
> Checked by AVG - www.avg.com
> Version: 9.0.830 / Virus Database: 271.1.1/2961 - Release Date: 06/24/10
> 14:35:00
>
> ----
> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
> To support QSL/QTH.net: http://www.qsl.net/donate.html
>
>    

----
Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
Icom Users Net: Sundays, 1700Z, 14.316 MHz
Icom FAQ: http://www.qsl.net/icom/
To support QSL/QTH.net: http://www.qsl.net/donate.html