[ICOM] AFSK RTTY with PROIII

[Len Morris VE3FJB]

Well what I would do, is pull and the jumpers, and start again. If you have 
a scope or ohm meter, work back from acc1 pin one and make sure your getting 
the FSK... Try looking at the Circuit board and see if there are any cold 
solder joints.
If all else works but the FSK, that is the route I would take..
Frustrating Eh!
On a positive point I got my CI-V working with the amp (PW-1) had to do a 
real hard reset..
Hang in there.
Len

----- Original Message ----- 
From: "Phil Krichbaum" <vailphil at sopris.net>
To: "ICOM Reflector" <icom at mailman.qth.net>
Sent: Wednesday, January 06, 2010 3:39 PM
Subject: Re: [ICOM] AFSK RTTY with PROIII


> Len,
>    I can manually short the FSK pair from the ACC plug and hear the
> tone shift. I've checked the jumpers at least 20 times. When it goes
> into transmit (PTT works) I get a solid tone
>    Phil
>
>
> Len Morris VE3FJB wrote:
>> Well Phil, I am sure this is a silly question, do you have the jumpers in
>> the Blaster set right?
>> Can you use a scope of voltmeter to see if the FSK voltage is changing on
>> ACC 1 pin 1?
>> Do you get PTT from the Blaster..?
>>
>> I have not used a rigblaster, but I understand the jumpering can be less
>> than clear. I have used the resistor, transistor to key both FSK and PTT,
>> then I went to the Rig Expert, and now the Navigator, mostly for the 
>> Codec..
>> Just pulled my ProIII out of the rack and installed the 7700, and having
>> trouble with the CI-V talking to the amp, worked with the ProIII !
>> So it never ends! hi
>>
>> Not sure what I else I can suggest..
>>
>> Len
>>
>>
>>
>> ----- Original Message ----- 
>> From: "Phil Krichbaum" <vailphil at sopris.net>
>> To: "ICOM Reflector" <icom at mailman.qth.net>
>> Sent: Wednesday, January 06, 2010 2:29 PM
>> Subject: Re: [ICOM] AFSK RTTY with PROIII
>>
>>
>>
>>> Len
>>>    If I could get the Rig Blaster Plus to work with MMTTY and N1MM in
>>> FSK that would solve the problem. I do have the FSK key line out of the
>>> ACC connector but can't get the software to send FSK. Unfortunately I've
>>> not been able to solve that and was looking for a work around in the
>>> meantime with AFSK where I could use the RTTY filters in RX. It might be
>>> an scenario that could be possible but was overlooked by Icom in the
>>> design of the PROIII.
>>>    Phil N0KE
>>>
>>> Len Morris VE3FJB wrote:
>>>
>>>> Hi Phil, just do the FSKing in the ACC 1 connector at the back as shown
>>>> on
>>>> Sec 2 page 20 that is where I got my fixed lever AF as well.. MMTTY 
>>>> under
>>>> options set the com # you get your FSK..
>>>> GL
>>>> Len
>>>> VE3FJB/VA3LM
>>>>
>>>> ----- Original Message ----- 
>>>> From: "Phil Krichbaum" <vailphil at sopris.net>
>>>> To: "Icom" <icom at mailman.qth.net>
>>>> Sent: Wednesday, January 06, 2010 1:32 PM
>>>> Subject: [ICOM] AFSK RTTY with PROIII
>>>>
>>>>
>>>>
>>>>
>>>>>    Maybe I missed it, but no where in the manual can I see how to use
>>>>> the 350 Hz RTTY filter when using AFSK in LSB. Using the 1800 Hz 
>>>>> filter
>>>>> position plus the twin PBT it is reasonably OK down to about 900 Hz 
>>>>> but
>>>>> no narrower to receive RTTY effectively. Now if I could get the Rig
>>>>> Blaster Plus to transmit FSK with N1MM and MMTY, I wouldn't have to
>>>>> worry about this problem!
>>>>>    Phil N0KE
>>>>> ----
>>>>> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
>>>>> Icom Users Net: Sundays, 1700Z, 14.316 MHz
>>>>> Icom FAQ: http://www.qsl.net/icom/
>>>>> To support QSL/QTH.net: http://www.qsl.net/donate.html
>>>>>
>>>>>
>>>> ----
>>>> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
>>>> Icom Users Net: Sundays, 1700Z, 14.316 MHz
>>>> Icom FAQ: http://www.qsl.net/icom/
>>>> To support QSL/QTH.net: http://www.qsl.net/donate.html
>>>>
>>>>
>>>>
>>> ----
>>> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
>>> Icom Users Net: Sundays, 1700Z, 14.316 MHz
>>> Icom FAQ: http://www.qsl.net/icom/
>>> To support QSL/QTH.net: http://www.qsl.net/donate.html
>>>
>>
>> ----
>> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
>> Icom Users Net: Sundays, 1700Z, 14.316 MHz
>> Icom FAQ: http://www.qsl.net/icom/
>> To support QSL/QTH.net: http://www.qsl.net/donate.html
>>
>>
> ----
> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
> To support QSL/QTH.net: http://www.qsl.net/donate.html