[ICOM] Using Microham Microkeyer II with IC7600

[Joe - WDØM]

The CI-V address for the 7600 is:  7A  The 7700 address is:  74  Try 7A 
to see if it works.  If not, Gary's suggestions  below are on target.  
Some of the 7700 features may not work with the 7600 as expected, but 
they should be close.

73

Joe
WDØM

Gary P. Fiber wrote:
> You do have the flexibility to change the CI-V address of the IC-7600 to 
> something the microKeyer has in its listing.
> You might give up a CI-V function or two. I am sure the other things 
> like the AFSK, FSK, CW keying will work fine as those are not software 
> related unless the microKeyer uses CI-V commands to make those features 
> function. Icom surely does not change the CI-V command number for each 
> product so most CI-V commands will be common between both the IC-7600 
> and IC-7700. There may be a feature difference between the 2 products 
> though.
> You may need to download both the 7600 and 7700  manuals to print out 
> the CI-V commands from each to compare them.
> The microKeyer looks to be a pretty nifty product. Have you contacted 
> the microKeyer company to see about updates to their product?
>
> Gary K8IZ
>
>
>
> John Gaynard wrote:
>   
>> Interface cable is the same cable - same pinout.  It's the rig in the setup
>> option that is missing.  I tried the IC7700 option in setup and it did not
>> seem to work - probably wrong CI-V address.
>>
>> John K8WDN
>>
>> -----Original Message-----
>> From: icom-bounces at mailman.qth.net [mailto:icom-bounces at mailman.qth.net] On
>> Behalf Of Gary P. Fiber
>> Sent: Thursday, December 03, 2009 1:56 PM
>> To: ICOM Reflector
>> Subject: Re: [ICOM] Using Microham Microkeyer II with IC7600
>>
>> Just looking at the web page for this device I'd bet it will work fine 
>> providing the IC-7600 has the proper inputs. I'd also suspect the 7600 
>> and 7700 support much of the same pin out BUT I have not looked at 
>> either manual for those products. You may have to roll your own 
>> interface cable.
>>
>> Gary K8IZ
>>
>>   
>>     
>
>   
>> John Gaynard wrote:
>>   
>>     
>>> Does anyone use the Microham Microkeyer II with the IC7600.  The IC7700
>>> appears in the rig list but not the IC7600.  The interface cable is the
>>>     
>>>       
>> same
>>   
>>     
>>> as the IC756ProIII
>>>
>>>  
>>>
>>> John
>>>
>>> John Gaynard K8WDN
>>>
>>> ----
>>> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
>>> Icom Users Net: Sundays, 1700Z, 14.316 MHz
>>> Icom FAQ: http://www.qsl.net/icom/
>>> To support QSL/QTH.net: http://www.qsl.net/donate.html
>>>
>>>   
>>>     
>>>       
>> ----
>> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
>> Icom Users Net: Sundays, 1700Z, 14.316 MHz
>> Icom FAQ: http://www.qsl.net/icom/
>> To support QSL/QTH.net: http://www.qsl.net/donate.html
>>
>> ----
>> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
>> Icom Users Net: Sundays, 1700Z, 14.316 MHz
>> Icom FAQ: http://www.qsl.net/icom/
>> To support QSL/QTH.net: http://www.qsl.net/donate.html
>>
>>   
>>     
>
> ----
> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
> To support QSL/QTH.net: http://www.qsl.net/donate.html
> ------------------------------------------------------------------------
>
>
> No virus found in this incoming message.
> Checked by AVG - www.avg.com 
> Version: 9.0.709 / Virus Database: 270.14.93/2544 - Release Date: 12/04/09 00:32:00
>
>