[ICOM]PW-1 ALC

[Steve]

Thanks for the clarification Adam.

And thanks Gary N6LRV for sending the the pdf direct.

Steve K8JQ

Adam Farson wrote:
> Hi Steve, 
> 
> It is actually under a link which read "Get IIC-PW1 Documents". I can see
> that the URL was somewhat ambiguous.
> 
> To correct this, I have renamed the link "IC-PW1 Service Manual etc."
> 
> Cheers for now, 73,
> Adam VA7OJ/AB4OJ
> 
> 
> -----Original Message-----
> From: icom-bounces at mailman.qth.net [mailto:icom-bounces at mailman.qth.net] On
> Behalf Of Steve
> Sent: 16 January 2006 14:15
> To: ICOM Reflector
> Subject: Re: [ICOM]PW-1 ALC
> 
> Adam,
> 
> I looked through the IC-PW1 links at www.qsl.net/icom/manuals.html but do
> not find the service manual you reference.
> 
> Would you be so kind as to point me to it?
> 
> Thanks.
> 
> Steve K8JQ
> 
> Adam Farson wrote:
> 
>>Hi Tony,
>>
>>The ALC pots are R1 and R2 on the JACK-1 board. One can order them 
>>from Icom Parts (P/N 7310003820).
>>
>>You will need the service manual to tackle repairs. The manual is 
>>downloadable here:
>>
>>http://www.qsl.net/icom/manuals.html
>>
>>In the meantime, you can use the Exciter 2 position.
>>
>>Cheers for now, 73,
>>Adam VA7OJ/AB4OJ
>> 
>>
>>-----Original Message-----
>>From: icom-bounces at mailman.qth.net 
>>[mailto:icom-bounces at mailman.qth.net] On Behalf Of Tony Visco
>>Sent: 15 January 2006 15:48
>>To: 'ICOM Reflector'
>>Subject: RE: [ICOM]PW-1 ALC
>>
>>
>>Ouch,
>>
>>I was installing a new exciter and was adjusting the ALC which is a 
>>little difficult because of my remote location for the Linear.  
>>Unfortunately I feel it is difficult to feel the adjusting screw move 
>>and of course the plastic adjustment made a snap sound which meant I 
>>may have pushed a little hard.
>>
>>It is now on a bit of an angle and of course the ALC is spiking over 
>>the recommended setting.
>>
>>Is this a component that is accessible?? If so could I likely adjust 
>>it with the damaged plastic adjustment?
>>
>>Is this a component that can be replaced by me?
>>
>>Any helpful advice will be appreciated.
>>
>>Tony W3EW
>>
>>
>>
>>Scanned for viruses by Blue Coat
>>http://www.WinProxy.com/
>>----
>>Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net Icom 
>>Users Net: Sundays, 1700Z, 14.316 MHz Icom FAQ: 
>>http://www.qsl.net/icom/
>>
> 
> ----
> Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net Icom Users
> Net: Sundays, 1700Z, 14.316 MHz Icom FAQ: http://www.qsl.net/icom/
> 
> 
> 
> Scanned for viruses by Blue Coat
> http://www.WinProxy.com/
> ----
> Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
>