[Ham-Mac] flrig 1.4.3.14 posted

[w1hkj]

at http://www.w1hkj.com/alpha/flrig/

	flrig-1.4.3.14.tar.gz 
<http://www.w1hkj.com/alpha/flrig/flrig-1.4.3.14.tar.gz> 	2021-12-12 
15:35 	951K 	
	flrig-1.4.3.14_BS.dmg 
<http://www.w1hkj.com/alpha/flrig/flrig-1.4.3.14_BS.dmg> 	2021-12-12 
15:35 	3.4M 	
	flrig-1.4.3.14_HS.dmg 
<http://www.w1hkj.com/alpha/flrig/flrig-1.4.3.14_HS.dmg> 	2021-12-12 
15:35 	2.0M 	
	flrig-1.4.3.14_LI.dmg 
<http://www.w1hkj.com/alpha/flrig/flrig-1.4.3.14_LI.dmg> 	2021-12-12 
15:35 	1.8M 	
	flrig-1.4.3.14_setup..> 
<http://www.w1hkj.com/alpha/flrig/flrig-1.4.3.14_setup.exe> 	2021-12-12 
15:35 	1.3M 	
	flrig-shell <http://www.w1hkj.com/alpha/flrig/flrig-shell> 	2021-12-12 
15:35 	9.3K 	
	readme.dmg.txt <http://www.w1hkj.com/alpha/flrig/readme.dmg.txt> 
2021-12-12 15:35 	555 	
	readme.txt <http://www.w1hkj.com/alpha/flrig/readme.txt> 	2021-12-12 
15:35 	2.8K 	


Please report back on viability of voltage display for the supported 
Icom transceivers.  Actual CAT data and published response strings did 
not agree for my 7300.  If the voltage display is not accurate you can 
provide calibration data for me.  I need readings for at least 2 power 
supply voltages,  12.0 and 13.0 would be ideal.  Open the "Send Command" 
panel on the configuration dialog.  The read voltage command is "x15 
x15".  For example:



Press "ICOM pre", enter x15 x15.  Press ICOM post.  Press SEND. Record 
the response.  repeat for at least two different power supply voltages 
(if possible).

Date:   Sun Dec 12 12:54:00 2021 -0600 alpha 1.4.3.14

## - changed from 1.4.3.13

##    IC756 pro
       * Add missing code to set mode A/B

##    Volt meter
       * Add visible volt meter for supported transceivers
         . IC-705
         . IC-7300
         . IC-705
         . IC-7100
         . IC-7600
         . IC-7610
         . IC-9700

     Documentation
       * update documentation

##    tmate2
       * add support for Elad TMATE-2 control interface

     XmlRpc modify exchange
       * add xmlrpc exchange structures to modify specific
         transceiver parameters:
         . rig.mod_vfoA d:d modify vfoA by +/- NNN
         . rig.mod_vfoB d:d modify vfoB by +/- NNN
         . rig.mod_vol  n:i modify volume by +/- NNN
         . rig.mod_pwr  n:i modify power by +/- NNN
         . rig.mod_rfg  n:i modify rf gain by +/- NNN
         . rig.mod_wpm  i:s modify CW WPM by +/- NNN
         . rig.mod_bw   i:i modify bandwidth by +/- NNN
           bw modified to nearest requested new value
       * correct get/set/modify vfoA/B
         . Fl::awake call was using a volatile parameter pointer

     Signal Bar
       * Change peak detect and averaging algorithm

     FT450D power out
       * change conversion method CAT string to power out
         update submitted by Brian Waterworth, VE3IBW

     Power Meter Autoscale
       * remove conflicting code causing unstable
         display

     fl_alert messages
       * correct wording in transceiver not responding alerts

     FreqControl
       * remove FL_RED revers colorization used for testing

     code cleanup
       * remove compile WARNINGS

     embedded/dialog tabs
       * allow user to embed extra's tabs in main dialog
       * save & restore state of tabs dialog / embedded tabs
       * restore visibility of selected tab
       * add configurable tab colors
       * retain state of tabs when changing between embedded
         and dialog visualization
       * retain visibility of embedded tabs when changing
         between small and large sliders
       * retain tab selection color between executions
       * adjust width of tabs dialog to width of main dialog

     cwio-timing
       * accu_sleep not reentrant or thread safe
         - create unique copy of now() and accu_sleep(double)
           for singular use by cwio thread
       * add execution of [ ] control characters when at beginning
         and end of text buffer respectively

     fsk
       * add ability to send FSK signals on DTR or RTS serial
         line, either shared or separate serial port.
       * implement accurate nanosecond timing for Linux, OS-X
         and Windows targets
       * add winmm lib for Windows build
       * correct mark/space levels for RTTY lower sideband signalling

     IC7800 time set
       * Change in support.cxx to enable viewing Misc extras
         tab for transceivers supporting date-time set methods

     Version 1.4.3


73, David, W1HKJ