[GreenKeys] ASR 33 - another question about the reader

[Teletypeparts]

Alf,

I have seen the top of the readers warped without a crease, but it could also be just the plastic cover or the metal plate that sits in front of the reader that stays bolted to the pan pushing on the reader metal.  Also if you have a 3 piece cover, you can adjust the plastic reader cover fit to the main cover.  When the reader is adjusted properly to the cover, it will run quietly.  When the cover or plate is pushing on it, it will run with a much louder clunking sound.  Visual, visual, visual is the rule on 33 fixes.  

73's

Wayne






-----Original Message-----
From: Alf Fisher <alf_fisher at tiscali.co.uk>
To: Packard42 <Packard42 at gmail.com>; Teletypeparts <teletypeparts at aol.com>
Cc: greenkeys <greenkeys at mailman.qth.net>
Sent: Mon, Apr 18, 2011 3:50 am
Subject: Re: [GreenKeys] ASR 33 - another question about the reader


Don & Wayne,
Many thanks for your comment and helpful suggestions.  I will have a look at it tomorrow to see if the top plate is bent up. 
IIRC, it looks OK at a quick glance.  I assume there would be creasing of the metal somewhere if it was bent.
I just thought that the feed sprocket and tape out sensor were all mounted on the frame and it all needs raising up a bit. 
Perhaps there a diagram in the TTY manual?
 
73
Alf

----- Original Message ----- 
From: Teletypeparts 
To: Packard42 at gmail.com ; alf_fisher at tiscali.co.uk 
Cc: greenkeys at mailman.qth.net 
Sent: Monday, April 18, 2011 12:04 AM
Subject: Re: [GreenKeys] ASR 33 - another question about the reader


Alf and Don,
 
Sorry to interject, but those 4 screws under the reader only adjust the tape reader to the cover for best fit.  If the feed sprocket is low, likely the brushed aluminum top plate has been bent up and must be carefully bent back to original fit.  Also its possible that the cover is pushing on the top plate and then the 4 screws may help.  
 
The reader stopping is almost surely the tape out contacts which can be easily adjusted by bending them both, but if the frame is bent as described above, that would be the first thing to fix.  With the cover off do a lot of visual checks before making any adjustments.
 
73's
 
Wayne






-----Original Message-----
From: Don Robert House <Packard42 at gmail.com>
To: Alf Fisher <alf_fisher at tiscali.co.uk>
Cc: greenkeys <greenkeys at mailman.qth.net>
Sent: Sun, Apr 17, 2011 6:10 pm
Subject: Re: [GreenKeys] ASR 33 - another question about the reader


Yes Alf,
nder the reader is a central lock nut.  Surrounding the lock nut are  
our adjusting screws to position the reader to operate properly.
n addition sometimes the contacts come out of the comb that holds  
hem in place. You can usually see and reposition them if necessary.
Don
9TTY
On 17 Apr 2011, at 3:17 AM, Alf Fisher wrote:
Don et al,
>From reading the question posed by Bill, it prompts me to ask about a  
roblem I have with the reader on the museum ASR33.
It will run if I hold down the cover but for some reason it stops when  
 let it go.
I think it could be the Tape Out sensor but I also noticed the tape  
rive sprocket seems a bit low down and doesnt engage properly with  
he holes in the tape.
s the protrusion of the whole assembly adjustable?
Any ideas?
Regards,
lf
3WSD

_____________________________________________________________
reenKeys mailing list
ome: http://mailman.qth.net/mailman/listinfo/greenkeys
elp: http://mailman.qth.net/mmfaq.htm
ost: mailto:GreenKeys at mailman.qth.net
This list hosted by: http://www.qsl.net
lease help support this email list: http://www.qsl.net/donate.html