[Elecraft] Sticky low TX power level after ATU activation?
Jack Brindle
jackbrindle at me.com
Tue Oct 27 15:59:18 EDT 2026
Looking at the original post, having two matching units in series is a prescription for problems. I understand the idea is that the Matchbox brings the antenna to close to an unbalanced 50 ohm condition, and then the K3 ATU matches the Tx into that 50 ohm line. But, if things change (say the window-line gets wet), which do you retune? The correct answer is the Matchbox, which handles open-wire properly. If instead the op expected the K3’s ATU to handle this, then his experience is exactly what I would expect. At this point the line characteristics it sees are way off what was originally set, and it may not be able to find a match.
You really want to remove one of the match units, either the Matchbox or the K3 ATU. The Matchbox is better suited to handle the window-line fed antenna, and indeed will provide the exact match you need. But, it takes time to manually tune it, and if you are in a contest, you will be losing QSOs (and points). While I far prefer using tank-circuit tuners for my open-wire antennas, because of the time I have chosen to go another way, using a balun and choke at the window line, with beefy coax back to the K3’s ATU. You want the coax to be as short as possible so as to minimize losses in the coax. There are some conditions where the ATU will be able to properly tune the line (although maybe close to 2:1 at the transmitter), but the coax will see a much higher mismatch, and thus lots of loss. Worse, this presents conditions to the balun that may cause it to fail, especially if you are running power (e.g. a KPA500 or KPA1500).
For this of us who contest, the real solution is to use properly matched antennas that provide close to a 50 ohm resistive condition across the band, and thus need no matching. This is really hard to do on 80 or 160 meters, a situation I haven’t mastered either.
I see changes in your antenna system ahead. As much as I love open-wire fed antennas, coax fed is the right way to go for some stations. And having two matching units in series is almost always a problem about to happen. My 1KW Johnson Matchbox now sits alone unused (sigh).
73,
Jack, W6FB
> On Oct 27, 2026, at 7:41 AM, Michael Carter via Elecraft <elecraft at mailman.qth.net> wrote:
>
> [this post duplicates my post of yesterday to the Elecraft-K3 at groups.io forum; thought I would try here as well for those who use the official Elecraft forum]
>
> In this past weekend's CQWW SSB contest, I observed a phenomenon that I had occasionally encountered in CW contests. I have a K3 with the KPA3A PA module and the original KAT3 ATU installed. I use a single 66 foot center-fed doublet (450 ohm window line) on bands from 80 through 10 meters to a Johnson Matchbox as the first impedance transformer, then use the internal ATU to make the TX happy. I have previously found Matchbox settings that yield moderately low SWR on each band, certainly well within the KAT3 matching capability.
>
> What I noticed this weekend is that when I tuned across the phone segments of each band, I had to activate the ATU to remove the 'HIGH SWR' warning that popped up from time, which I did. However, on the next transmission after that ATU activation, the TX output power was very low. On a whim, I did one of those ATU activations, then rotated the POWER control knob a bit down and back up. The TX power was again at its high setpoint (~ 100 watts).
> I think the sticky low TX power after ATU activation was less noticeable in CW contests because the tuning range is more limited, typically the lower 60 kHz of each band except on 10 meters during a big opening. The extent of the phone segments meant more SWR variation across the segment and the need for more ATU activations.
>
> Is this a known behavior of the TX power control? I know it automatically ratchets down the TX power when the ATU is activated, but it seemed that the TX power 'stuck' at the low ATU tuning level until the POWER control knob was rotated.
>
> Thanks for any insights!
>
> 73,
> Mike, K8CN
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to jackbrindle at me.com
More information about the Elecraft
mailing list