[Elecraft] sdr play and K3S

[Barry]

Bob
     I have been using the SDRPlay to drive Win4k3. It works with little 
problem. That problem is setting the global offset so that it matches 
exactly your K3s. Not all SDR software will play nicely being driven by 
the SDRPlay. And, BTW; If you are going to use narrows roofing filters, 
you are going to need to account for the fact that each has a slightly 
different calibration frequency. It's no big deal, but it should be set 
for your specific radio.

73,
Barry
K3NDM
------ Original Message ------
From: "Bob McGraw K4TAX" <rmcgraw at blomand.net>
To: "Don Sayler" <dons at ieee.org>
Cc: "Elecraft Reflector" <elecraft at mailman.qth.net>
Sent: 4/9/2020 9:42:53 PM
Subject: Re: [Elecraft] sdr play and K3S

>I’ve used the RSP-1a with HDSDR.  I had to set the calibration for overall and then for each mode. Some values were + and some - .  Also I found my SDR Play RSP-1a does drift noticeably.
>
>Finall tossed the thing in the drawer and purchased a P3.  Much more satisfactory.
>
>Bob, K4TAX
>
>
>Sent from my iPhone
>
>>  On Apr 9, 2020, at 8:28 PM, Don Sayler <dons at ieee.org> wrote:
>>
>>  Hi Everyone.
>>
>>
>>
>>  I've been trying to get my SDRPlay (w/ SdrUno) to work with the IF output of
>>  my K3S.
>>
>>  I've got OmniRig set up, so the K3S and SdrUno interact properly. Well,
>>  almost.
>>
>>
>>
>>  There seems to be an offset between the K3S frequency and the SdrUno
>>  frequency. For example, I dial in WWV at 10 MHz on the K3S, and SdrUno hears
>>  the signal at ~9.875 MHz.
>>
>>  On 80m, this offset is around 117KHz.  I've tried the setting the External
>>  Converter offsets, that didn't help.
>>
>>
>>
>>  In SdrPlay, I do have the IF Output Frequency set to 8125000 Hz and it is
>>  enabled. I've tried adjusting this value a little, and it didn't seem to
>>  help.
>>
>>  I am aware of some of the limitations of SdrUno compared to other software,
>>  but this is the one that I'm used to. I may switch to another one at some
>>  point.
>>
>>
>>
>>  Any ideas? I looked through the K3S config settings, and nothing jumped out
>>  at me.
>>
>>
>>
>>  Thanks!
>>
>>
>>
>>  73,
>>
>>  Don W7OXR
>>
>>
>>
>>  ______________________________________________________________
>>  Elecraft mailing list
>>  Home: http://mailman.qth.net/mailman/listinfo/elecraft
>>  Help: http://mailman.qth.net/mmfaq.htm
>>  Post: mailto:Elecraft at mailman.qth.net
>>
>>  This list hosted by: http://www.qsl.net
>>  Please help support this email list: http://www.qsl.net/donate.html
>>  Message delivered to rmcgraw at blomand.net
>>
>
>
>______________________________________________________________
>Elecraft mailing list
>Home: http://mailman.qth.net/mailman/listinfo/elecraft
>Help: http://mailman.qth.net/mmfaq.htm
>Post: mailto:Elecraft at mailman.qth.net
>
>This list hosted by: http://www.qsl.net
>Please help support this email list: http://www.qsl.net/donate.html
>Message delivered to barrylazar2 at gmail.com