[Elecraft] CODEC

[Bob McGraw K4TAX]

While I use both WSJT-X, V1.9.1,  and HRD, I allow WSJT to create and 
save its own log.  Then I transfer the entries from the WSJT log to my 
other log system.  That then uploads the selected entries to LOTW.    
I've more often than not found that if I allow one software to run 
within or under another software, there's just two many cooks in the 
kitchen tasting the pot.     In other words, I run WSJT as a stand a 
lone application and do not have any conflicts.  The operating system is 
a current version of Windows 10 with all of their updates.

As suggestions, I would open WSJT as a stand a lone and see if it 
connects to the rig and operates correctly.   Then close WSJT and open 
HRD using one of its modes, i.e. PSK-31, and see if it operates 
correctly.    If so on both, and mine does, then there is no specific 
issue with either application or the computer or the radio.   I use the 
USB communication with my K3S.  Then with both applications running I 
find is the area where the hand shake is supported to occur but indeed a 
fist fight breaks out.   That says HRD will need to be update in order 
for Windows 10 to handle the activity.  The bottom line, when Microsoft 
updates Windows 10, all other application software is likely in need of 
an update as well.

Good luck in resolving the issue.

73

Bob, K4TAX


On 10/1/2018 12:36 PM, ROBERT MUELLER wrote:
> Mike, I would be interested in what you find.  Since Microsoft and then HRD did upgrades I have not been able to get WSJT to work with HRD and my K3S, therefore, the logging from FT* to HRD will not work.  When I try to set things up I get a message:   Hamlib error: IO error while opening connection to rig.  I am running a USB cable which worked fine until all the upgrades.  Very interested in what you find.
> Bob, k8rgm at comcast.net
>> On October 1, 2018 at 11:49 AM Mike Greenway <K4PI at BELLSOUTH.NET> wrote:
>>
>>
>> I have used for years a K3 on EME with WSJT using Line In/Out audio.  Recently got a K3S and I am now using USB (CODEC) audio in and out of the radio.  In WSJT-10 they have Rate In/Rate Out monitors that should normally run at 1.000. Using the K3 analog audio these always stayed right on 1.000 but now that I am using the USB audio they are jumping around quite often and getting out of range indicated in WSJT with a red marker.  I have tried two different computers and the same result.  I tried changing the sample rate in the computer audio settings but no change in the problem.  I plan to go back to analog Line In/Out on the K3S unless someone has an idea on how to settle down the Rate In/Out fluctuations.  I have not found anything in the K3S that might affect this.  You can reply off line if you like.  73 Mike K4PI
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to k8rgm at comcast.net
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to rmcgraw at blomand.net
>