[Elecraft] K3 Mini Error question

[Mitch Wolfson, DJØQN / K7DX]

Jim,

This involves primarily configuring the radio side router to forward the 
correct UDP ports. It must be thoroughly tested before leaving the radio 
site on its own.

I have a checklist setup that walks you through this process and will 
forward it to you now in a separate mail.

73,
Mitch  DJ0QN / K7DX

Mitch Wolfson DJØQN / K7DX
10285 Boca Cir, Naples, FL 34109
Skype: mitchwo
USA: Home:+1-239-221-9600 - Mobile:+1-424-288-9171
Germany: Home:+49 89 32152700 - Mobile:+49 172 8374436

On 29.10.2016 17:44, Jim Cary wrote:
> John/Barry
>
> Thanks for the quick responses.   I’ll be setting up the other side tomorrow.  I think when I had them working at home I had both units connected before I fired up the mini, so I didn’t have the problem.
>
> 73,
>
> Jim
>
>
>> On Oct 29, 2016, at 5:39 PM, John <john at eeek.org.uk> wrote:
>>
>> Jim,
>>
>> This is actually quite a simple one, luckily!
>>
>> I'm assuming when you say RRC you mean the MicroHAM RemoteRig Control system - I've helped set these up and test them for a couple of years now, so assuming I've got that bit right...
>>
>> It simply means that it's unable to talk to the other end (ie the kit you haven't connected at the far end).
>>
>> The MicroHAM RRC systems use SIP over UDP on three different ports - one for voice data, one for CAT data, and one for control signals between the remote head and the unit body. If it's a SIP connection error you're seeing, it's because the two ends of the RRC system can't see each other (which, as you say, is the correct case because you haven't hooked up the remote unit yet).
>>
>> If I'm barking up the wrong tree, please correct me.
>>
>> 73, and a firm left handshake,
>> John (XLX)
>>
>> -----Original Message-----
>> From: Elecraft [mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Jim Cary
>> Sent: 29 October 2016 22:27
>> To: elecraft at mailman.qth.net
>> Subject: [Elecraft] K3 Mini Error question
>>
>> I just packed up both my control and remote systems and moved them down to my ZF QTH, where they will be permanent.
>>
>> I have the K3 mini hooked up to the control RRC unit, but haven’t hooked up the remote unit yet/
>>
>> When I powered up the mini, and turned the volume control I got a three tone warning signal.  The light over the aux/mic cable is flashing yellow, which according to the Remote Rig manual means the SIP connection has failed…. but it isn’t clear what that means or what to do about it.  I’ve checked and doubled checked all the connections and they look good.
>>
>> Does anyone not in the CQ contest (!!!) have an idea?
>>
>> Jim
>> W2SM
>> ZF2LC
>>
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html Message delivered to john at eeek.org.uk
>>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to dj0qn at arrl.net