[Elecraft] VOX SET Command?

[Randy Diddel]

Hello Bill,

A toggle should be easy at least in terms of programming. A set command
with a 0 or 1 would be all it would take. The programmer's manual I have
states one will be made available in the future. My question was if we were
'there yet' and does anyone know the syntax if it had.

73

/randy

On Fri, Nov 28, 2014 at 10:56 PM, Nr4c <nr4c at widomaker.com> wrote:

> VOX is a toggle. Don't think you can set a toggle button, only toggle it.
>
> Sent from my iPhone
> ...nr4c. bill
>
>
> > On Nov 28, 2014, at 11:54 PM, Randy Diddel <k5rhd at arrl.net> wrote:
> >
> > Hi Joel,
> >
> > I will look into doing just that.  Still looking for an answer about VOX
> > SET and if the command exists yet.
> >
> > Freeing up PF2 for the setup I use on SOTA would be a real bonus-I use a
> > Heil Headset and usually have to manually set that up on the mountain.
> >
> > 73
> >
> > K5RHD
> >
> > /randy
> >
> >> On Fri, Nov 28, 2014 at 8:09 PM, Joel Black <joel.b.black at gmail.com>
> wrote:
> >>
> >> Randy,
> >>
> >> If you wish, you can make them so each macro calls the other: one long
> >> hold brings up the data mode; the second long hold brings up voice;
> another
> >> long hold brings up data; and so on.
> >>
> >> I don’t have my KX3 out at the moment, but here’s what my macro looks
> like
> >> going from CWSPLT to UNSPLT:
> >>
> >> CWSPLT -
> MD3;SWT25;SWT25;FT1;SB1;UPB4;MN142;MP001;MN110;SWT27;SWH18;MN255;
> >> UNSPLT - SB0;FR0;MN142;MP000;MN110;SWT19;SWH18;MN255;
> >>
> >> The last four commands of CWSPLT tell it MN110 (MACRO x); SWT27 (x=2);
> >> SWH18 (program PF1 [with Macro 2 {from SWT27 where x=2}]); MN255 (exit
> >> menu).
> >>
> >> The last four commands of UNSPLT tell it MN110 (MACRO x); SWT19 (x=1);
> >> SWH18 (program PF1 [with Macro 1]); MN255 (exit menu).
> >>
> >> That way, you long press the PFx button each time you want to go back
> and
> >> forth. You can save the other PFx button for something else (I turn on
> and
> >> off the ATU depending on the antenna I’m using). I will say this took a
> >> couple of hours of experimenting with the KX3 and the macros. There was
> one
> >> macro for which I was watching its output. The KX3 programming software
> was
> >> very handy for this.
> >>
> >> Good luck.
> >>
> >> 73,
> >> Joel - W4JBB
> >>
> >>> On Nov 28, 2014, at 7:16 PM, Randy Diddel <k5rhd at arrl.net> wrote:
> >>>
> >>> Good evening, night, day, etc.
> >>>
> >>>
> >>> I have been working hard on getting my KX3 programmed to switch between
> >>> voice and digital modes using a string of commands assigned to PF1 and
> >>> PF2.  I have them working perfectly except for setting VOX to ON for
> data
> >>> modes.  In the programmer's manual from Elecraft, it states that "A SET
> >>> version of the command is planned."  Has this been implemented?  Does
> >>> anyone know the syntax?
> >>>
> >>> For those interested here are the two strings:
> >>>
> >>> For Data:  MD6;PA0;MG005;AG001;DT0;BW0400;PC12;PC015;ML000;
> >>> For Voice:  MD2;MG005;BW0240;SWH34;PA1;ML000;AG040;PC110;PA0;
> >>>
> >>> These real
>