[Elecraft] VOX SET Command?

[Randy Diddel]

Hi Joel,

I will look into doing just that.  Still looking for an answer about VOX
SET and if the command exists yet.

Freeing up PF2 for the setup I use on SOTA would be a real bonus-I use a
Heil Headset and usually have to manually set that up on the mountain.

73

K5RHD

/randy

On Fri, Nov 28, 2014 at 8:09 PM, Joel Black <joel.b.black at gmail.com> wrote:

> Randy,
>
> If you wish, you can make them so each macro calls the other: one long
> hold brings up the data mode; the second long hold brings up voice; another
> long hold brings up data; and so on.
>
> I don’t have my KX3 out at the moment, but here’s what my macro looks like
> going from CWSPLT to UNSPLT:
>
> CWSPLT - MD3;SWT25;SWT25;FT1;SB1;UPB4;MN142;MP001;MN110;SWT27;SWH18;MN255;
> UNSPLT - SB0;FR0;MN142;MP000;MN110;SWT19;SWH18;MN255;
>
> The last four commands of CWSPLT tell it MN110 (MACRO x); SWT27 (x=2);
> SWH18 (program PF1 [with Macro 2 {from SWT27 where x=2}]); MN255 (exit
> menu).
>
> The last four commands of UNSPLT tell it MN110 (MACRO x); SWT19 (x=1);
> SWH18 (program PF1 [with Macro 1]); MN255 (exit menu).
>
> That way, you long press the PFx button each time you want to go back and
> forth. You can save the other PFx button for something else (I turn on and
> off the ATU depending on the antenna I’m using). I will say this took a
> couple of hours of experimenting with the KX3 and the macros. There was one
> macro for which I was watching its output. The KX3 programming software was
> very handy for this.
>
> Good luck.
>
> 73,
> Joel - W4JBB
>
> > On Nov 28, 2014, at 7:16 PM, Randy Diddel <k5rhd at arrl.net> wrote:
> >
> > Good evening, night, day, etc.
> >
> >
> > I have been working hard on getting my KX3 programmed to switch between
> > voice and digital modes using a string of commands assigned to PF1 and
> > PF2.  I have them working perfectly except for setting VOX to ON for data
> > modes.  In the programmer's manual from Elecraft, it states that "A SET
> > version of the command is planned."  Has this been implemented?  Does
> > anyone know the syntax?
> >
> > For those interested here are the two strings:
> >
> > For Data:  MD6;PA0;MG005;AG001;DT0;BW0400;PC12;PC015;ML000;
> > For Voice:  MD2;MG005;BW0240;SWH34;PA1;ML000;AG040;PC110;PA0;
> >
> > These really help out as I can be working JT65 and see a new one on the
> > clusters, switch over, and jump in the side band pile up.  VOX works best
> > with WSJT-X and my specific configuration-that is why it would be good to
> > have a bit to set it ON in the string listed above and a bit to switch it
> > off when I switch to voice mode.
> >
> >
> > 73
> >
> > K5RHD
> >
> > /randy
> > ______________________________________________________________
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft at mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> > Message delivered to w4jbb at charter.net
>
>