[Elecraft] CW on SSB

[Sam Morgan]

I believe you will find it under CW Weight in the manual

here is the snipit from the manual

CW WGHT 1.15 Adjusts element/space timing ratio (weight) for the 
internal keyer.
Additional functions of this menu entry, via numeric keypad (Advanced):
Tap 1 to select SSB -CW (default) or SSB +CW (allows CW in SSB modes).
Tap 2 to select @ = STOP (‘@’ character terminates KY-packet transmission;
default) or @ = ‘AC’ (‘@’ in a KY packet is sent as .--.-. [@] in CW mode).
Tap 3 to select OLD or NEW QSK (default). NEW reduces AF keying artifacts.
Tap 4 to select VOX NOR (default) or AUTO OFF. The AUTO OFF setting
turns CW VOX off on power-up, avoiding accidental keying by attached 
PCs, etc.
Tap 5 to select automatic VFO offset on SSB/CW mode change (VFO OFS) or
no offset (VFO NOR, default). Automatic offset is often used on 6 
meters, where
mixed-mode QSOs are necessary during fading. Note: Pitch matching will be
more accurate if USB is paired with CW REV, and LSB with CW normal.

I think it is the Tap 5 part
sm

On 5/15/2014 11:12 AM, Edward R Cole wrote:
> I give up...didn't find any "Autoshift" in the menus of either the K3 or
> KX3.  Is this about some other radio?  Or is a feature of some early vs
> of firmware long gone?  I'll admit not updating the K3 lately (vs 4.81).
>
> In doing frequency drift measurements I noted that Frequency seen in USB
> mode is different than what is seen in CW mode.  The shift appears to be
> that of the sidetone frequency which I have set to 550-Hz for performing
> the temperature compensation procedure on the KX3.
>
> To hear the test signal in USB I have to retune the VFO if I switch from
> CW.  I have a good ear for tone frequency so am able to tune in the test
> signal in USB to match the CW sidetone frequency.  That requires moving
> the dial about 550 Hz.  If on the wrong sideband you will *not* hear it.
>
> 73, Ed - KL7UW
>
> ---------------------
> From: Oliver Dr?se <droese at necg.de>
> To: elecraft at mailman.qth.net
> Subject: Re: [Elecraft] CW on SSB
> Message-ID: <5373DE83.5090801 at necg.de>
> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
>
>
> And enable auto-shift in the menu when switching from CW to SSB and vice
> versa, otherwise you will still have to retune to get signal into the
> passband again.
>
> 73, Olli
>
> Contest, DX & radio projects: http://www.dh8bqa.de
>
> 73, Ed - KL7UW
> http://www.kl7uw.com
>      "Kits made by KL7UW"
> Dubus Mag business:
>      dubususa at gmail.com
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to k5oai.sam at gmail.com
>

-- 
GB & 73
K5OAI
Sam Morgan