[Elecraft] K3 - second receiver for split ?

[W0MU Mike Fatchett]

Check the K3 manual there are some good button programs included like up 
2  up 5 and cleanup which will take you out of split.

Mike W0MU

On 4/18/2014 8:01 PM, Martin Kratoska wrote:
> I use a macro based on ZL2IFB's suggestions:
>
> RT0;XT0;FR0;DV0;BW0040;SWT13;SWT13;UP4;SB1;BW0100;MN111;MP002;MN255;
>
> It is assigned to PF1 (RIT button), you can do the job with K3 utils.
>
> It copies the actual frequency to VFO B, moves the VFO 1 UP, sets on 
> the corresponding filters. Now you listen the DX on your KRX3 while 
> the main RX/TX is on the calling frequency. You can use QSK/QRQ while 
> operating split.
>
> I operate almost exclusively CW. For SSB you should modify the filter 
> bandwidth and the UP shift (up 5 probably...).
>
> 73,
> Martin, OK1RR
>
> Dne 18.4.2014 16:46, Jim Miller napsal(a):
>> I had just noticed those lines but didn't think they were necessarily 
>> the
>> transmit freq as I was in CW and the line wasn't at 600 as I would have
>> expected.  Figured it was new for something but did not further research
>> them at the time.  I had my width wide to see the pileup and with it 
>> in the
>> middle, no help.
>>
>> I am new at split.  Can I run split using my second receiver for the
>> transmit freq??  Then narrow the receive width on the transmit 
>> frequency vfo
>> so the line would be where it belongs???
>>
>> Thanks, 73, Jim KG0KP
>>
>> -----Original Message-----
>> From: Jim Rogers [mailto:jim.w4atk at gmail.com]
>> Sent: Friday, April 18, 2014 6:33 AM
>> To: Jim Miller
>> Subject: Re: [Elecraft] K3 - Transmit signal monitor display on my P3 
>> - show
>> location when split
>>
>> It does.  VFO A is the green line and VFO B is the cyan line, If you 
>> are on
>> SSB it also shows the pass band  as either upper or lower sideband by 
>> which
>> side of the marker it is on. CW will be centered in the pass band.
>>
>> 73s JIm, W4ATK
>> On 4/18/2014 6:15 AM, Jim Miller wrote:
>>> I want my signal to show me on my P3 where I am transmitting  split.
>>> 73, Jim KG0KP
>>>
>>>
>>> ______________________________________________________________
>>> Elecraft mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>>> Help: http://mailman.qth.net/mmfaq.htm
>>> Post: mailto:Elecraft at mailman.qth.net
>>>
>>> This list hosted by: http://www.qsl.net Please help support this email
>>> list: http://www.qsl.net/donate.html Message delivered to
>>> jim.w4atk at gmail.com
>>>
>>
>>
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to martin at ok1rr.com
>>
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to w0mu at w0mu.com