[Elecraft] Help with a Macro from the K3 to turn on the KAP500

[Tom]

Ok could be undocumented.
Lets hope Wayne chimes in.

Tom
va2fsq.com

Sent from my iPhone

On 2013-07-17, at 5:25 PM, William Levy <wglevy at gmail.com> wrote:

> Not what Wayne says.
> 
> On Jul 17, 2013, at 3:24 PM, Tom <tomb18 at videotron.ca> wrote:
> 
>> 
>> Hi
>> Yes they talk to each other but only send band change info and certain other statuses. To do this with only a macro and no possible hardware is not possible
>> 
>> Tom 
>> va2fsq.com
>> 
>> Sent from my iPhone
>> 
>> On 2013-07-17, at 5:06 PM, William Levy <wglevy at gmail.com> wrote:
>> 
>>> Yes, but they are connected directly in the back of the K3 with one of the AUX cables so they feed each other that way.
>>> Thus the K3, Amp and ATU all talk to each other.
>>> Thus the need to be able from the K3 to turn on the Amp.
>>> Bill N2WL
>>> 
>>> 
>>> On Jul 17, 2013, at 1:02 PM, Tom wrote:
>>> 
>>>> Hi
>>>> That would be news to me, since the k3 and kpa use different serial ports.
>>>> Tom
>>>> va1fsq.com
>>>> 
>>>> Sent from my iPhone
>>>> 
>>>> On 2013-07-17, at 2:24 PM, William Levy <wglevy at gmail.com> wrote:
>>>> 
>>>>> Somewhere I thought there was written a short macro to designate a button
>>>>> on the K3 to turn on the Amp from the K3.
>>>>> 
>>>>> Any help with that would be greatly appreciated. This old ham has his fist
>>>>> in to too many old radios at the moment to sit down and figure out code.
>>>>> Too busy reading resistor codes. All  help appreciated. Thanks, Bill N2WL
>>>>> ______________________________________________________________
>>>>> Elecraft mailing list
>>>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>>>>> Help: http://mailman.qth.net/mmfaq.htm
>>>>> Post: mailto:Elecraft at mailman.qth.net
>>>>> 
>>>>> This list hosted by: http://www.qsl.net
>>>>> Please help support this email list: http://www.qsl.net/donate.html
>> Sent from my iPhone
>> 
>> On 2013-07-17, at 5:06 PM, William Levy <wglevy at gmail.com> wrote:
>> 
>>> Yes, but they are connected directly in the back of the K3 with one of the AUX cables so they feed each other that way.
>>> Thus the K3, Amp and ATU all talk to each other.
>>> Thus the need to be able from the K3 to turn on the Amp.
>>> Bill N2WL
>>> 
>>> 
>>> On Jul 17, 2013, at 1:02 PM, Tom wrote:
>>> 
>>>> Hi
>>>> That would be news to me, since the k3 and kpa use different serial ports.
>>>> Tom
>>>> va1fsq.com
>>>> 
>>>> Sent from my iPhone
>>>> 
>>>> On 2013-07-17, at 2:24 PM, William Levy <wglevy at gmail.com> wrote:
>>>> 
>>>>> Somewhere I thought there was written a short macro to designate a button
>>>>> on the K3 to turn on the Amp from the K3.
>>>>> 
>>>>> Any help with that would be greatly appreciated. This old ham has his fist
>>>>> in to too many old radios at the moment to sit down and figure out code.
>>>>> Too busy reading resistor codes. All  help appreciated. Thanks, Bill N2WL
>>>>> ______________________________________________________________
>>>>> Elecraft mailing list
>>>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>>>>> Help: http://mailman.qth.net/mmfaq.htm
>>>>> Post: mailto:Elecraft at mailman.qth.net
>>>>> 
>>>>> This list hosted by: http://www.qsl.net
>>>>> Please help support this email list: http://www.qsl.net/donate.html
>