[Elecraft] K3 won't shut off?

[Dr. William J. Schmidt, II]

I found the problem... There is a jumper inside the preamp that needs to be
removed when used with the K3 and the accessory connector.  I thought I
removed it when it arrived, but I guess my age is starting to show...


Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ

Owner - Operator
Big Signal Ranch
Staunton, Illinois

email:  bill at wjschmidt.com


-----Original Message-----
From: dseven at dseven.org [mailto:dseven at dseven.org] On Behalf Of iain
macdonnell - N6ML
Sent: Monday, December 31, 2012 4:04 PM
To: bill at wjschmidt.com
Cc: Elecraft Mailing List
Subject: Re: [Elecraft] K3 won't shut off?

I would check inside the DE15 connector - maybe something is shorting pin 8
to ground inside there.

73,

    ~iain / N6ML


On Mon, Dec 31, 2012 at 1:49 PM, Dr. William J. Schmidt, II
<bill at wjschmidt.com> wrote:
> Yes, it works fine with the preamp completely removed...
>
>
> Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
>
> Owner - Operator
> Big Signal Ranch
> Staunton, Illinois
>
> email:  bill at wjschmidt.com
>
> -----Original Message-----
> From: dseven at dseven.org [mailto:dseven at dseven.org] On Behalf Of iain 
> macdonnell - N6ML
> Sent: Monday, December 31, 2012 3:18 PM
> To: bill at wjschmidt.com
> Cc: Elecraft Mailing List
> Subject: Re: [Elecraft] K3 won't shut off?
>
> Does the K3 power off fully if you disconnect the ACC connector? It 
> sounds like something is pulling pin 8 down....
>
> 73,
>
>     ~iain / N6ML
>
>
> On Mon, Dec 31, 2012 at 12:20 PM, Dr. William J. Schmidt, II 
> <bill at wjschmidt.com> wrote:
>> So I connected my PR6 - 6 meter preamp to my K3 for the first time 
>> last week and work some DX.  At the end of the day I go to shut the 
>> radio off and the display goes blank (hear the relays disengage) but 
>> all of the LEDs are still lit on the radio. and it will not turn back 
>> on except to cycle the power on the power supply.  I discuss this 
>> with a friend and he reminds me that there was a MOD for K3's to put 
>> a diode on the KPA3 board for the 12V sense circuit, but after 
>> looking at the MOD sheet on the Elecraft website, it says that this 
>> MOD was incorporated into the radio as of 2009 (my radio less than a 
>> year old).  I remove the fans to check for the 1N4148 on P68A of the 
>> KPA3 and it's not there.  So two questions. Has anyone else 
>> experienced this phenomena, and does anyone know. was that diode 
>> actually incorporated
> into the radio on the board somewhere else and mine is just bad?
>>
>>
>>
>>
>>
>> Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ/ PJ4HZ
>>
>>
>>
>> Owner - Operator
>>
>> Big Signal Ranch
>>
>> Staunton, Illinois
>>
>>
>>
>> email:   <mailto:bill at wjschmidt.com> bill at wjschmidt.com
>>
>>
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net Please help support this 
>> email
>> list: http://www.qsl.net/donate.html
>