[Elecraft] P3 beta, A/B operation

[Stephen Prior]

Guy,

None of those settings make any difference as far as I can see.

73 Stephen

On 23 June 2011 19:16, Guy Olinger K2AV <olinger at bellsouth.net> wrote:

> Does the rounding off change with the various settings of FINE,
> COARSE, either on the front panel or CONFIG:VFO CRS, or mode?
>
> 73, Guy.
>
> On Thu, Jun 23, 2011 at 2:55 AM, Stephen Prior <eastbrantwood at gmail.com>
> wrote:
> > Alan, I'm sorry to say this but nothing seems to have changed for me in
> the
> > rounding off.  It will be interesting to note what others find.
> >
> > 73 Stephen G4SJP
> >
> >
> >
> > On 23 June 2011 07:21, Alan Bloom <n1al at sonic.net> wrote:
> >
> >> Actually, there was a bug introduced in 1.08.  Try this:
> >>
> >> 01.09 is at ftp.elecraft.com/tmp/P3/alpha/
> >>
> >> Alan
> >>
> >> On Sun, 2011-06-19 at 13:04 +0100, Stephen Prior wrote:
> >> > I made exactly the same observation to Alan N1AL.  He managed to
> persuade
> >> me
> >> > that it had always been like that ;-)
> >> >
> >> > 73 Stephen G4SJP
> >> >
> >> > On 19 June 2011 06:25, Corin & Alan <alanandcorin at yahoo.com> wrote:
> >> >
> >> > >
> >> > >
> >> > > I sometimes use the A/B to switch between the CW and phone section
> of a
> >> > > band.  I like to set the P3 to FixMode and adjust the right edge to
> >> align
> >> > > with the band edge, say 14.000.0.  So if I set VFO A to 14.025 in CW
> >> mode
> >> > > and switch to VFO B at 14.240 also in CW mode I can switch back and
> >> forth
> >> > > and the edge shown on the P3 stays set to 14.000.0.  However, if VFO
> B
> >> is
> >> > > set to 14.250 in USB, when I switch back to VFO A the edge shown on
> the
> >> P3
> >> > > changes to 14.001.5?  Huh?  Otherwise, I like to new cursor and
> >> > > improvements.
> >> > >
> >> > > 73s, Al, K6IV
> >> > > ______________________________________________________________
> >> > > Elecraft mailing list
> >> > > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> >> > > Help: http://mailman.qth.net/mmfaq.htm
> >> > > Post: mailto:Elecraft at mailman.qth.net
> >> > >
> >> > > This list hosted by: http://www.qsl.net
> >> > > Please help support this email list: http://www.qsl.net/donate.html
> >> > >
> >> > ______________________________________________________________
> >> > Elecraft mailing list
> >> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> >> > Help: http://mailman.qth.net/mmfaq.htm
> >> > Post: mailto:Elecraft at mailman.qth.net
> >> >
> >> > This list hosted by: http://www.qsl.net
> >> > Please help support this email list: http://www.qsl.net/donate.html
> >> >
> >>
> >>
> >>
> > ______________________________________________________________
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft at mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> >
>