[Elecraft] K3 Micro Manual iPhone App

[Michael Downs]

If you are a K3 owner/operator, you may be interested in a new iPhone application. I call it the K3 Micro Manual as it incorporates most of the K3 Owner's Manual in a handy iPhone format. It is compatible with iPhone (iOS 3.1.3 and later), iPod Touch and iPad. It has been updated to include the Owner's Manual Errata, and all firmware changes since the Owner's Manual was published. Thus, it is current through November 14, 2010. In addition, I have included operating tips from the Elecraft web site, selected emails from the Elecraft Reflector,  and  operating experience.

If you think you may be interested in this app, it is now available in the Apple App Store. It is listed under the Reference category. Just search for "K3 Owners Manual" or "ks7d."  I welcome your input on enhancements to this application, and for your favorite operating tips. I plan updates over time to this app to keep it current with the latest Elecraft Owner's Manual, and to add new features.

Following is the table of contents for the app:

K3 Micro Manual Table of Contents:
 
Overview of Application
Introduction
Key to Symbols
Table of Contents

Controls and Connectors
Introduction
Primary Controls
Display
Multi-Function Controls
Keypad
Memories
VFOs
RIT/XIT
Rear Panel Connectors
KIO3 Connectors
KXV3 Connectors

Quick-Start
Introduction
Connections
The Basics
Filter Controls
Voice Modes
CW Mode
Data Modes
VFOs and RIT/XIT
Transmit, ATU and Ant
NB, NR and Notch
SPLIT, BSET and SUB
Memories, Messages and DVR
Menus and Switch Macros
Other Features

Basic Operation
Fundamentals
Receiver Setup
Reducing Interference
Transmitter Setup
Voice Modes
CW Mode
Data Modes

Advanced Operation
Text Decode and display
CW-to-DATA
Tuning Aids: CWT and SPOT
Audio Effects (AFX)
Dual Passband CW Filtering
Receive Audio EQ
Transmit Audio EQ
SPLIT and Cross-Mode
Extended Single Sideband (ESSB)
General-Coverage RX
VFO B Alternate Displays
Alarm and Auto Power-On
Using the Sub Receiver
Receive Antenna In/Out
Buffered I.F. Output
Using Transverters
Scanning

Remote Control
Introduction
Remote-Control Commands
Front-Panel Switch Macros
Remote Power On/Off
Automatic Antenna Control
CW/DATA Terminal Applications
K3 Memory Editor

Options and Accessories
Introduction
Options and Accessories

Firmware Upgrades
Introduction
Checking your Firmware Revision
K3 Firmware Self-Test
Forcing a Firmware Download

Configuration
Introduction
Crystal filter Setup
Option Module Enables
Miscellaneous Setup

Calibration Procedures
Introduction
Synthesizer
Wattmeter
Transmitter Gain
Reference Oscillator
FP Temp Sensor
PA Temp Sensor
S-Meter and RF Gain

MAIN Menu Functions
Introduction
AFX MD
ALARM
...
ANTIVOX

CONFIG Menu Functions
Introduction
2 TONE
ADC REF
...
XVn ADR

Troubleshooting
Common Symptoms
Parameter Initialization
Module Troubleshooting
Error Message List

Operating Tips
Introduction
CW/DX Operating Scenario
Using TX TEST
AFX (Audio Effects)
RTTY Operation w/o PC
VFO B Display Modes
Add Text to ANT1/ANT2
RIT/XIT Techniques
Setup for PSK
QRO/Battery Operation
Adjust ATU L-C Settings
RIT with VFO A Knob
KK7P Explains NR
Menu Help Text
Operating at 500 kHz
FW Load Failure Recovery
Operating in Split Mode
60 Meter Band Operation

Firmware Release Notes
Introduction
MCU 4.14/DSP 2.60
MCU 4.13/DSP 2.60
MCU 4.12/DSP 2.60
MCU 4.06/DSP 2.60
MCU 4.05/DSP 2.60
MCU 4.03/DSP 2.60
MCU 3.97/DSP 2.58
MCU 3.94/DSP 2.54
MCU 3.84/DSP 2.54

Hopefully, I can follow this iPhone version with a version for Android phones. I need to get an Android phone to test the application on before it is released. Testing in the emulator is fine, but it must be checked out on actual hardware before release.

73,
Mike ks7d