[Elecraft] K3: ADC Ref calibration

[VK5ABQ]

I spend most of my time tinkering with the AGC-THR, AGC-SLP and RX-EQ - wish
I had a dollar for every minute I've spent with the RX-EQ but that's The
Other thread.



Matt Zilmer wrote:
> 
> You have the satisfaction of knowing that your're right on the mark
> then.  Well... at least very close.  AND you've been spot on the whole
> time you've had the K3.
> 
> Suggestion:  Find somewhere else to tinker.  The S-Meter is a good
> target.  There has been some debate on that.  Same with AGC
> adjustments.
> 
> There is a lot to do here with the K3.  Operating it is the best part.
> I think Elecraft has found us a whole new hobby, or a set of them.
> 
> 73,
> matt, W6NIA
> K3 #24, K2 #2810, etc.
> 
> 
> On Mon, 15 Dec 2008 20:39:28 -0800 (PST), you wrote:
> 
>>
>>The multimeter *did* read 5.007 volts but I couldn't enter the additional
7mV
>>into the K3. Talk about annoying.... 
>>
>>
>>Matt Zilmer wrote:
>>> 
>>> Just use a different (uncalibrated) DMM....  Then you can change the
>>> setting _twice_!
>>> 
>>> matt zilmer, W6NIA
>>> 
>>> On Mon, 15 Dec 2008 18:07:07 -0800 (PST), you wrote:
>>> 
>>>>
>>>>Don't you hate it when your calibrated multimeter displays 5.00V on pin
2
>>of
>>>>the ACC connector and you then don't have a reason for altering the
>>setting?
>>>>I feel like I've missed out :)
>>>>
>>>>
>>>>-----
>>>>Shane
>>>>K3/10: S/N 2127, KBPF3, KFL3B-FM, KFL3A-6K, KFL3A-2.8K, KFL3A-400,
>>KTCXO3-1
>>>>& KXV3.
>>> _______________________________________________
>>> Elecraft mailing list
>>> Post to: Elecraft at mailman.qth.net
>>> You must be a subscriber to post to the list.
>>> Subscriber Info (Addr. Change, sub, unsub etc.):
>>>  http://mailman.qth.net/mailman/listinfo/elecraft
>>> 
>>> Help: http://mailman.qth.net/subscribers.htm
>>> Elecraft web page: http://www.elecraft.com
>>> 
>>> 
>>
>>
>>-----
>>Shane
>>K3/10: S/N 2127, KBPF3, KFL3B-FM, KFL3A-6K, KFL3A-2.8K, KFL3A-400,
KTCXO3-1
>>& KXV3.
> _______________________________________________
> Elecraft mailing list
> Post to: Elecraft at mailman.qth.net
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft
> 
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
> 
> 


-----
Shane
K3/10: S/N 2127, KBPF3, KFL3B-FM, KFL3A-6K, KFL3A-2.8K, KFL3A-400, KTCXO3-1
& KXV3.
-- 
View this message in context: http://n2.nabble.com/K3%3A-ADC-Ref-calibration-tp1658417p1661575.html
Sent from the Elecraft mailing list archive at Nabble.com.