[Elecraft] K3 Band Data

[Greg - AB7R]

Yes and that was my intent as well....to provide options.  That's why the IF was capitalized.  :)


-------------------------
73,
Greg - AB7R
Whidbey Island WA
NA-065


On Fri Dec  5  9:42 , "Joe Subich, W4TV"  sent:

>
>> Not true of the KRC2 IF you are using the 
>> AuxBus line. 
>
>The question was specifically with respect to BCD output - 
>not Aux Bus.  Neither the microHAM Band Decoder not Station 
>Master require any modification (or care about the BCD 
>coding) if the serial (CAT) data is used for band decoding 
>but that wasn't the question that Jan asked.    
>
>Another respondent mentioned an specific band decoding device 
>from one vendor.  My response was to provide the data about 
>the other available products that Jan was likely to be using 
>as well as get the full information into the archives so 
>another person searching for the same information in two or 
>three years from now was not left to wonder about compatibility 
>with devices other than one specific product. 
>
>73, 
>
>   ... Joe, W4TV 
> 
>
>
>> -----Original Message-----
>> From: Greg - AB7R [ab7r at cablespeed.com','','','')">ab7r at cablespeed.com] 
>> Sent: Friday, December 05, 2008 11:30 AM
>> To: '' Jan Erik Holm ''; elecraft at mailman.qth.net; 'Joe; Subich; W4TV'
>> Subject: RE: [Elecraft] K3 Band Data
>> 
>> 
>> The Elecraft KRC-2 and  >W9XT Band Decoders do not have 
>> pull-up resistors and will  >require the addition of 2.2 - 
>> 10K resistors   Not true of the KRC2 IF you are using the 
>> AuxBus line.  I have the K3 ACCY AuxBus connected to the KRC2 
>> and it  works great.  No changes needed.  
>> ------------------------- 73, Greg - AB7R Whidbey Island WA 
>> NA-065   On Fri Dec  5  7:37 , "Joe Subich, W4TV"  sent:  > 
>> >The BCD encoding is the same as the FT-1000D/FT-2000.  > 
>> >Interfacing to a microHAM or TopTen Band Decoder requires  
>> >no internal modification (both products include pull-up  
>> >resistors on their BCD inputs).  The Elecraft KRC-2 and  
>> >W9XT Band Decoders do not have pull-up resistors and will  
>> >require the addition of 2.2 - 10K resistors in the decoder  
>> >or on the KIO3 board as documented in the Negative ALC  >Mod 
>> bulletin.  > >73,  > >   ... Joe, W4TV  >  > > > >> 
>> -----Original Message----- >> From: 
>> elecraft-bounces at mailman.qth.net  >> 
>> [elecraft-bounces at mailman.qth.net','','','')">elecraft-bounces
>> @mailman.qth.net] On Behalf Of Jan Erik Holm >> Sent: Friday, 
>> December 05, 2008 4:00 AM >> To: Elecraft Reflector >> 
>> Subject: [Elecraft] K3 Band Data >>  >>  >> Is the K3 band 
>> data compatible with Yaesu (ex:FT1000D) >> BCD band data. 
>> Looks to me that it is, or? >>  >> 73 Jim SM2EKM >>  >> 
>> _______________________________________________ >> Elecraft 
>> mailing list >> Post to: Elecraft at mailman.qth.net >> You must 
>> be a subscriber to post to the list. >> Subscriber Info 
>> (Addr. Change, sub, unsub etc.): >>  
>> http://mailman.qth.net/mailman/listinfo/elecraft     >>  >> 
>> Help: http://mailman.qth.net/subscribers.htm >> Elecraft web 
>> page: http://www.elecraft.com > 
>> >_______________________________________________ >Elecraft 
>> mailing list >Post to: Elecraft at mailman.qth.net >You must be 
>> a subscriber to post to the list. >Subscriber Info (Addr. 
>> Change, sub, unsub etc.): > 
>> http://mailman.qth.net/mailman/listinfo/elecraft     > >Help: 
>> http://mailman.qth.net/subscribers.htm >Elecraft web page: 
>> http://www.elecraft.com  
>> 
>