[Elecraft] Logger32

[Jack Brindle]

There is another way to do what you want (assuming I understand what  
you want...). Use the SW09 command to toggle between the two VFOs.  
This is the same as tapping the A/B key, and does not cancel SPLIT mode.

On Oct 9, 2007, at 1:33 PM, Mike Harris wrote:

> G'day Joe,
>
>> From the KIO2 programmer's ref:
>
> FR (RX VFO Assignment and SPLIT Cancel; GET/SET)
>
> SET/RSP format: FRn; where n specifies the receive/transmit VFO: 0  
> for VFO
> A and 1 for VFO B.
>
> Sending an FR SET command always cancels SPLIT mode.
>
> So, it looks like there is no option but to remember to re initiate  
> split
> every time.  There are times when you can toggle between two  
> targets when
> using the bandmap, split required in each case.  To lose the split  
> when
> toggling sadly sometimes leads to the dreaded UP, UP lid!
>
> I guess if it didn't work this way there would be an equal number  
> of split
> instead of simplex errors.  Win some lose some.
>
> I use CW reverse above 20M to keep the tuning sense consistent.
>
> Regards,
>
> Mike VP8NO
>
>
>
> | Mike,
> |
> | FR0 sets the receiver to VFO A - which is appropriate when
> | clicking on a spot (set operation to the main VFO or main receiver),
> | set frequency, then set the transmit frequency if different and
> | finally turn on split).
> |
> | It is the MD3; command that is setting normal CW (MD3; is CW,
> | MD7; is CW-R).  The discussion with any software author needs to
> | be to support CW-R if you generally operate CW-R instead of CW.
> | Some software allows the user to specify CW or CW-R as the default
> | when clicking on a spot but that choice is used for all spots
> | (it is, after all, necessary to set the mode when clicking on a
> | spot).
> |
> | 73,
> |
> |   ... Joe, W4TV
> |
> |
> |
> |
> | > | Mike Harris wrote:
> | > | > G'day,
> | > | >
> | > | > Been checking the command from Logger32 to the K2 when  
> directly
> | > entering a
> | > | > frequency eg. 18073kHz:
> | > | >
> | > | > FR0;FA00018073000;MD3;FA00018073000;
> | > | >
> | > | > FRO cancels split and presumably CW reverse as well.
> | > | >
> | > | > Bugger!
> | > | >
> | > | > Regards,
> | > | >
> | > | > Mike VP8NO
> | > | >
> | > | >
> | > | >
> | > |
> | > |
> | > | --
> | > | No virus found in this incoming message.
> | > | Checked by AVG Free Edition.
> | > | Version: 7.5.488 / Virus Database: 269.14.1/1050 - Release Date:
> | > 04/10/2007 17:03
> | > |
> | > |
> | >
> | > _______________________________________________
> | > Elecraft mailing list
> | > Post to: Elecraft at mailman.qth.net
> | > You must be a subscriber to post to the list.
> | > Subscriber Info (Addr. Change, sub, unsub etc.):
> | >  http://mailman.qth.net/mailman/listinfo/elecraft
> | >
> | > Help: http://mailman.qth.net/subscribers.htm
> | > Elecraft web page: http://www.elecraft.com
> | >
> | >
> |
> |
> |
> | --
> | No virus found in this incoming message.
> | Checked by AVG Free Edition.
> | Version: 7.5.488 / Virus Database: 269.14.1/1050 - Release Date:
> 04/10/2007 17:03
> |
> |
>
> _______________________________________________
> Elecraft mailing list
> Post to: Elecraft at mailman.qth.net
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com


-Jack Brindle, W6FB
=======================================================================